Uponor T-75 - Exercise Actuators and Pumps; Temperature Unit; Backlight; Installer Level

www.uponor-usa.com • www.uponor.ca
32
Uponor Climate Co˘ntrol™ Zoning System Installation Guide
33
Section 9
Technical Data
General
• IP: IP30 (IP: degree of non-accessibility to the active
parts of the product and degree of non-accessibility
of water)
• Max. ambient relative humidity (RH): 95% max. at
68°F/20°C.
• Class II low-voltage device
Thermostat T-75
• Certication
- FCC Part 15 Subpart C
- Industry Canada Category I device
• Approval and certication:
- KNX: Konnex approval and certication
• Power supply: 2x Alkaline AAA 1.5V
• Voltage: 2.2V to 3.6V
• Operating temperature: 32°F/0°C to 113°F/45°C
• Storage temperature: 14°F/-10°C to 149°F/65°C
• Radio frequency: 902-928 MHz
• Transmitter duty cycle: 1%
Interface I-75
• CE marking:
- Low-voltage tests: EN 60730-1 and EN
60730-2-1
- EMC tests: EN 60730-1
• Power supply: 11VDC ±10% from controller
• Operating temperature: 32°F/0°C to 131°F/55°C
• Storage temperature: -4°F/-20°C to 158°F/70°C
• Consumption: 1W maximum
Antenna T55
• Power supply: 11VDC ±10% from controller
• Consumption: << 1W
• Radio frequency: 902 to 928 MHz
• Transmitter duty cycle: 1%
• Receiver Class: 2
Base Unit C-55
• Certication
- FCC Part 15 Subpart C
- Industry Canada Category I device
• Certication
- ICES-003
• Power supply: 90-130VAC, 60Hz Class II switching
power supply
• Operating temperature: 32°F/0°C to 131°F/55°C
• Storage temperature: -4°F/-20°C to 158°F/70°C
• Consumption: 70 W in full load max at 24VAC
• Demand contact: 24VAC at 2 Amps max (not fused)
• Valve outputs: 24VDC ±10%, 436 mA max. per
output 1 and 2 24VDC ±10%, 218 mA max. per
output 3 to 12
• Supply connection: terminal strip (push type)
polarity sensitive
* Do not substitute the external power supply. Damage to the controller
and hazardous conditions may occur. Warranty will be voided.
Use of Quick Connectors:
1. Without turning, use a thin screwdriver to press
the white button of the terminal to insert or
remove a wire.
2. Insert a wire in the quick connector.
3. Release the white button.
4. Run the cable in the cable guides secure it.
5. Screw clamp to secure the cable
of antenna or/and extension.
Exercise Actuators and Pumps
This exercise maintains the functionality of the
actuators and pumps. A ve-minute activation
is scheduled every week.
Cancel Exercise
1. Uponor screen
> Main Menu > Settings > System
Parameters
> Valve/Pump Exercise > Cancel Exercise
2.
> Press OK.
Exercise Valve and Pump
1. Uponor screen
> Main Menu > Settings > System
Parameters
> Valve/Pump Exercise > Exercise Valve
and Pump
2. Set the time and date for the
ve-minute activation.
> Press OK.
Exercise Actuator Only
1. Uponor screen
> Main Menu > Settings > System
Parameters
> Valve/Pump Exercise > Exercise
Valve Only
2. Set the time and date for the ve-
minute activation.
> Press OK.
Temperature Unit
1. Uponor screen > Main Menu >
Settings
> System Parameters >
Temperature Unit
2.
>°C or °F
> Press OK.
Backlight
1. Uponor screen > Main Menu >
Settings
> System Parameters >
Backlight
2. Select:
Always ON
Dimmed (when inactive): reduced screen brightness
OFF (when inactive): backlighting off
> Press OK.
Installer Level
The device has another mode: the Installer
level. Only the installer should set these
settings.
The Installer access level provides additional access to:
• The information menu
• All advanced level parameters
• Pump management settings
• Base unit identication
• Language
Vacation Mode
Vacation mode allows the user to easily set a temperature
reduction common to all rooms. The thermostat settings
are ignored during this period. The symbol
on the
Uponor screen indicates that the system is in
Vacation mode.
• The reduce vacation setpoint applies
throughout the installation for all installed
room thermostats. The setting range is
41°F to 95°F.
• The minimum and maximum limitations have
priority over the Vacation mode reduction.
For example if the minimum and maximum
temperature range of a room is set to 68°F
to 77°F, and the holiday temperature is set
to 59°F for all rooms, the temperature for
this room will not drop below 68°F.
Applying the Vacation Mode
1. Uponor screen > Main Menu > Vacation Mode >
Apply Vacation Mode
2. Enter time and date for the start
of the vacation period
> Press OK.
3. Enter time and date for the end
of the vacation period
> Press OK.
4. Enter the Vacation temperature
setpoint > Press OK.
Example: Vacation Mode can be cancelled before the
date is entered into the system.
Cancelling the Vacation Mode
1. Uponor screen > Main Menu > Vacation Mode >
Cancel Vacation Mode
2. Select Yes > Press OK.
Exercise Valve and Pump
Exercise Valve Only
Cancel Exercise
Exercise Setup
Monday
1 : 00
Exercise Time
Monday
1 : 00
Exercise Time
Please choose the
required temp unit.
˚C
˚F
Temperature Unit
Dimmed (when inactive)
OFF (when inactive)
Always ON
Backlight
14 Jan 2008
2 : 02
Set Date/Time
15 Jun 2008
2 : 02
End Date
59˚F
Vacation Te mperature
Cancel Vacation
Mode?
Ye s
No
Cancel Vacation Mode