Valor APR-101012 Series User Manual

Page 1 of 14
GEN2-V1 12ft-Instructions (Severe Weather) doc:r1
RETRACTABLE PATIO SHADE AWNING
Patio Awning Guide-10ft. x12ft.(Proj. X Width)
Model: APR-101012***/APR-60021012 (version: GEN2-V1)
1. INTRODUCTION:
Thank you for purchasing a Retractable Shade Awning. Before proceeding, please ensure that all the parts are in
the box, as listed below:
Master Carton Contents:
1-Box
labeled EXTENSION ARMS
1-Box
labeled LEFT WALL BRACKET ASSEMBLY
1-Box
labeled RIGHT WALL BRACKET ASSEMBLY
1-Box
labeled GEAR MECH. & Support Bracket
1-EA
180 cm Roller Tube, w/Square Drive
1-EA
180 cm Roller Tube, w/Round Drive
1-EA
50 mm Roller Tube Joiner
1-EA
180 cm Valance Tube, drilled left
1-EA
180 cm Valance Tube, drilled right
1-EA
50 mm Valance Tube Joiner, drilled
3-PCS
372cm Plastic Spline (coiled)
1-BAG
Bubble Bag, labeled MISC. PARTS, includes:
-2-Wrist Assemblies
-2-Position Poles
-Level
-6-Spline Stops
-Right & Left Valance Tube End Caps
-2-Bags of 4-1/2” x3” Sleeve Anchors
1-EA
160 cm Crank Handle
In the event that there is ANY part missing or damaged, please DO NOT RETURN THE PRODUCT TO YOUR
RETAILER. By returning the product to your retailer we can not assist you in getting your awning properly installed.
Call our TOLL FREE Customer Service Hotline at 1-888-875-4844 for parts or replacement of parts that may have
been damaged when shipped.
You may also go to our website at www.valor.ca in the Valor Shade/Patio Awning section for all assembly and
installation instructions, set up, adjustment, and troubleshooting instructions. There you will be able to see common
problems and how to rectify them usually with a simple adjustment. You may also use this section to email us your
questions, and during business hours between 9:00 AM and 4:00 PM EST you will be able to connect with a
customer service representative for assistance.
2. PRODUCT:
The Valor / Severe Weather™ Shade Awning is a unique program that allows you to order awnings that are modular
in design making them easier to transport home. The product is offered with your choice of several available patterns
(sold separately). The product is factory configured with Left Side operation (when facing the house), but can be
converted to right side operation by following the steps outlined in this guide.
IMPORTANT WARNING:
Your new awning is intended as protection against the sun only. It is not to be used during periods of strong
wind, rain, hail, or snow. The warranty will not cover use during these periods. Bird droppings, pine needles,
and various air born materials that may settle on your awning; awning fabric should be cleaned using water
and a light soap. No abrasive cleansers or harsh chemicals should be used on the fabric. Damage to the
Awning (including the fabric) from any foreign material is not covered under our warranty.
WARNING:
DO NOT CUT THE PLASTIC ZIP TIES ON THE AWNING EXTENSION ARMS UNTIL INSTRUCTED TO
DO SO IN THIS GUIDE. THE FOLDING ARMS ARE UNDER SPRING TENSION AND SHOULD NOT BE
CUT UNTIL THE AWNING IS FULLY ASSEMBLED AND INSTALLED ON THE WALL.

Valor APR-101012 Series Specifications

General

Brand	Valor
Model	APR-101012 Series
Category	Accessories
Language	English

Summary

Product Overview and Safety Warnings

Product Overview

General introduction to the retractable patio shade awning and its components.

Critical Safety Precautions

Essential warnings regarding spring tension, zip ties, and proper usage to prevent injury.

Installation Requirements

Tools Required for Installation

Lists all necessary tools for the awning installation process.

Additional Material and Hardware

Details on required header boards and specific fasteners for mounting.

Awning Schematic Diagram

Exploded View of Awning Components

Visual representation of all parts and their assemblies for the retractable awning.

Parts List and House Preparation

Complete Parts List

Comprehensive list of all parts included in the master carton with quantities.

House Preparation Guidelines

Instructions for ensuring a suitable mounting surface and checking wall integrity.

Header Board Installation Guidance

Header Board Material and Sizing

Recommendations for header board wood type, size, and cutting for a 12ft awning.

Siding Installation Considerations

Guidance for installing on vinyl, aluminum, steel, or wood siding, emphasizing stud mounting.

Determining Mounting Height and Header Board Mounting

Calculating Awning Mounting Height

Formula and guidelines for determining the optimal height for awning installation and clearance.

Mounting the Header Board to the Wall

Steps for positioning, leveling, and securing a header board using lag bolts and shims.

Marking and Bracket Installation

Marking Awning Position on Wall/Header

Procedures for marking horizontal and vertical center lines for awning placement.

Marking and Drilling Bolt Positions

How to precisely mark holes for mounting brackets using templates and measurements.

Attaching Wall Mounting Brackets

Instructions for positioning and marking the left and right side wall mounting brackets.

Awning Operation and Conversion

Left Side Awning Operation

Description of the default left-side operation configuration of the awning.

Converting to Right Side Operation

Step-by-step guide to reconfigure the awning for right-side operation.

Beginning Awning Assembly and Installation

Initial Assembly and Mounting Setup

Instructions for aligning bracket templates for drilling on the header board or wall.

Wall Bracket Installation Details

Installing Brackets on Masonry Surfaces

Method for mounting wall brackets using sleeve bolts on brick, stone, or concrete.

Installing Brackets on Header Board

Process for attaching wall brackets to a pre-installed header board using chosen fasteners.

Fabric and Tube Assembly

Roller Tube and Fabric Integration

Steps for joining roller tubes and inserting the main awning fabric with spline.

Valance Tube and Fabric Integration

Process for joining valance tubes and inserting the valance fabric with spline.

Component Installation and Arm Attachment

Installing Poles, Wrist Assemblies, and Level

Guides installation of position poles, wrist assemblies, and the level on the valance tube.

Attaching Extension Arms

Instructions for connecting the left and right extension arms to the respective wall brackets.

Connecting Valance Tube to Extension Arms

How to attach the valance tube to the ends of the extension arms using wrist pin bolts.

Tightening the Awning Fabric

Instructions for ensuring the fabric on the roller tube is taut and properly secured.

Final Touches and Adjustments

Installing Spline Stops and Tube End Caps

Securing spline stops and valance tube end caps to complete the awning structure.

Adjusting Awning Pitch

How to adjust the awning's pitch for optimal angle and even operation.

Fabric Roll and Arm Synchronization

Fine-tuning the fabric roll and synchronizing the extension arms for smooth opening/closing.

Fine-Tuning Extension Arm Operation

Adjusting Wrist Assemblies for Arm Movement

Detailed steps to adjust wrist assemblies for proper extension arm elbow movement and alignment.