Need help?Do you have a question about the Vaz 21214 and is the answer not in the manual?
Specifications for clutch, gearbox, transfer case, drive line, and axles.
Details on front and rear suspensions, wheel rims, and tire sizes.
Mechanism, linkage, and general steering system specifications.
Service braking system components, front/rear brakes, and handbrake.
Wiring, battery, alternator, and starter motor specifications.
Vehicle body type and construction details.
Step-by-step guide for engine removal and installation.
Procedures for disassembling engine components.
Guidelines for reassembling the engine after overhaul.
General description, inspection, and repair of the engine's cylinder block.
General description, selection, and assembly of pistons and connecting rods.
Design, inspection, and overhaul of crankshaft and flywheel.
Components, train, and clearance adjustment for cylinder head and valves.
Design, inspection, and adjustment of camshaft and timing gear.
Coolant checks, change, pump, thermostat, and radiator procedures.
Engine oil change and oil pump procedures.
Air cleaner, fuel tank, fuel pump, and injector maintenance.
General description, removal, dismantling, and adjustment of the carburettor.
EGR system operation and checks.
Exhaust manifold, pipes, and silencer components.
Design, fault diagnosis, and adjustment of the clutch system.
Fault diagnosis, removal, refitting, and dismantling of the gearbox.
Fault diagnosis, removal, refitting, and dismantling of the transfer box.
Propeller shaft inspection, removal, refitting, and balancing.
Design, fault diagnosis, and repair of the front axle.
Design, fault diagnosis, and repair of the rear axle assembly.
Component inspection, alignment angles, and removal/refitting procedures.
Design, removal/refitting, inspection, and testing of rear suspension components.
General inspection, check, and adjustment of the steering system.
Removal, refitting, and inspection of tie-rods and balljoints.
Removal, dismantling, inspection, and refitting of the idler arm bracket.
Fault diagnosis for braking efficiency, pedal feel, and noises.
Design, removal, dismantling, inspection, and replacement of front brake components.
Design, removal, dismantling, assembly, and inspection of rear brake components.
Handbrake removal, refitting, check, and repair.
Vehicle wiring system, fuse protection, and relevant diagrams.
Specifications, testing, and overhaul of the alternator.
Specifications, fault diagnosis, testing, and overhaul of the starter motor.
Distributor, spark control module, coil, and timing adjustment.
Headlights, turn signals, hazard flashers, and horn operation.
System description, fault diagnosis, and removal/refitting.
Instrument cluster components, fault diagnosis, and checks.
Procedures for repairing body damages, including paintwork.
Methods for ensuring body tightness with sealants and corrosion inhibitors.
Front door removal, refitting, dismantling, and alignment procedures.
Steps to remove, refit, and align the tailgate.
Removal, refitting, and adjustment of the bonnet and bumpers.
Replacement of glass and repair of washer systems.
Features of the VAZ-21214 model with Central Fuel Injection.
Details of the 4-cylinder, SOHC Sequential Fuel Injection engine.
Procedures for removing and refitting the VAZ-21214-20 engine.
Removal, refitting, dismantling, and repair of the central injection unit.
Procedures for checking fuel pressure and pump operation.
Examination and flushing of the EGR system.
EMS wiring harness, fuses, and protective links.
Differences for VAZ-21214 engine dismantling and reassembly.
Valve actuation, hydraulic lifters, and chain tensioner.
Coolant checks, change, pump, thermostat, and cambelt procedures.
Filter element renewal and crankcase ventilation.
Exhaust system components and their replacement.
Wiring diagrams for alternator, starter, EMS, and antitheft system.
General| Brand | Vaz |
|---|---|
| Model | 21214 |
| Category | Automobile |
| Language | English |
To Next Page
