6
If enabled and a busy is detected, the E-35 phone will dial the next programmed
speed dial number, and continue to cycle through the numbers until a call is
completed. * Notes: This feature is enabled in the factory default setting. If the busy
signal is interrupted with a promotional message, contact your central office to have
it removed.
Setting E - Dial Next Number on Busy
Setting F - Future Use (set to 1)
Setting C - Silence Time Out
This feature selects the length of time that calls will remain connected without voice
activity. Programmable in increments of 10 seconds up to a maximum of 90
seconds (Touch Tones 1 - 9). To disable the silence time out, program 0 in this
location. Use chart at the far right. * Note: The factory default is 40 seconds.
Setting D - Dial Next Number on Ring No Answer
If enabled and a ring-no-answer is detected, the E-35 phone will dial the next
programmed speed dial number, and continue to cycle through the speed dial
numbers until a call is completed.
* Note: Factory set to redial if not answered after 7 rings.
Touch Tone Silence Time Out
0 Disabled
1 10 seconds
2 20 seconds
3 30 seconds
4 40 seconds*
5 50 seconds
6 60 seconds
7 70 seconds
8 80 seconds
9 90 seconds
Touch Tone Setting D
1 or 0 Disabled*
2, 3, 4... 9
Dials second number
after 2, 3, 4...9 rings
respectively
Touch Tone Setting E
1 Disabled
2 Enabled*
F. Miscellaneous Options (memory location #17)
Dial: A +B+C+D+E+F+#+1+7
Factory Default Setting:0+0 +0+2+ 1+0
Not Applicable (enter 0)
Hang-up on Return to Dial Tone
Double Ring Cadence
Lap Counter
Enter Settings Here:
A B C D E F
0 0 0 #17
Setting B - Call Length Time Out
This feature selects the maximum length of time that calls can be connected.
Programmable in increments of 1 minute up to a maximum of 9 minutes (Touch
Tones 1 - 9). Program 0 in this location to disable the call length time out. With the
call length disabled, the E-35 phone must rely on a CPC signal, busy signal, silence
or return to dial tone to hang-up. Use chart at the right.
* Note: The factory default is 3 minutes.
Touch Tone Call Length Time Out
0 Disabled
1 1 minute
2 2 minutes
3 3 minutes*
4 4 minutes
5 5 minutes
6 6 minutes
7 7 minutes
8 8 minutes
9 9 minutes
E. Timing/Dialing Options (memory location #18)
There are six positions in the timing/dialing options. To program these options, enter the six desired timing/dialing
numbers followed by #18. The six available timing/dialing options are defined as follows:
Dial: A +B+C+D+E+F+#+1+8
Factory Default Setting: 2 + 3 +4+7+ 2+1
Talk/Listen Delay
Call Length
Silence Time Out
Dial Next Number on Ring No Answer
Dial Next Number on Busy
Future Use (set to 1)
Enter Timing/Dialing Settings Here:
A B C D E F
#18
Setting A - Talk/Listen Delay
This feature selects switching time between talk and listen modes (VOX switching
time). Use chart at the right. * Note: The factory default is .2 seconds.
Touch Tone Talk/Listen Delay
1 0.1 seconds
2 0.2 seconds*
3 0.3 seconds
4 0.4 seconds
5 0.5 seconds
6 0.6 seconds
7 0.7 seconds
8 0.8 seconds
9 0.9 seconds
To Next Page
Loading...
