Need help?Do you have a question about the Vintec V50SG e and is the answer not in the manual?
General| Capacity | 50 bottles |
|---|---|
| Installation | Freestanding |
| Number of Zones | 1 |
| Refrigerant | R600a |
| Reversible Door | Yes |
| UV Protection | Yes |
| Temperature Zones | Single |
| Temperature Range | 5°C to 18°C |
| Door Material | Glass |
Standard models of Vintec wine cellars.
Electronic regulation models with digital display.
Two-compartment models with electronic regulation.
Dual-zone wine cellars with electronic regulation.
Intended use for persons with reduced capabilities and child supervision.
Allow 24 hours before switching on; leave door open for odors.
Ensure unencumbered, well-ventilated space away from heat sources.
Use a standard, reliable, grounded outlet; avoid multi-sockets.
Distinguishes between free-standing, built-in, and partially built-in models.
Recommended ambient temperature range for optimal unit performance.
Ensures safety by grounding the appliance to reduce shock risk.
Advisable in locations with frequent lightning to protect the unit.
Remove packaging, position unit with accessible plug, avoid contact with compressor.
Use adjustable feet to ensure the wine cellar is perfectly level.
Attach the back spacer for proper ventilation and heat evacuation.
Crucial for ventilation; failure to attach voids warranty.
Press the power button; expect initial temperature stabilization.
Wait 3-5 minutes after power loss before restarting to prevent damage.
Describes gurgling, cracking/popping, and fan sounds as normal.
Load evenly, maintain gaps for air circulation, avoid overcrowding.
Adjust shelves for bottle size and stacking; do not overload.
Avoid obstructing fans, pulling shelves too far, or moving loaded unit.
Allow 24 hours for temperature stabilization after loading/settings.
Describes V30SG, V40SG, V50SG standard and 'e' models for storage/serving.
Explains V40DG/V50DG '2e' models with independent compartment regulation.
Details V30SG/V40SG/V50SG '2e' models for dual-zone wine serving.
Table showing default temperature settings for various models.
Wait 12 hours for effects; avoid frequent thermostat adjustments.
Explains 'MAX', 'NORMAL', 'MIN' settings for standard models.
Use the knob to set lower (clockwise) or higher (anti-clockwise) temperatures.
Explains TEMP. SET and DISPLAY LEDs for V30SG "e" model.
Use UP/DOWN buttons to adjust temperature in 1-degree increments.
Describes control panel for SG "e" and DG "2e" models.
Adjust temperature using UP/DOWN buttons from 5 to 18 degrees.
Press and hold UP/DOWN buttons to see set temperature flashing.
Overview of buttons for Upper/Lower chamber temperature settings.
Use Set Upper/Set Lower buttons for temperature adjustment (5-10°C upper, 10-18°C lower).
Indicative chart for optimal drinking temperatures for various wine types.
Constant temperature between 12°C-14°C is ideal for maturing wines.
Consistent temperature is more critical than the exact degree for wine storage.
Notes on wine aging capabilities and checking with wine merchants.
Explains the auto-cycle defrost system and condensation evaporation.
System maintains humidity for cork integrity; may require manual water addition.
Air circulates via fans and hollow shelves for temperature homogeneity.
Pull shelves out 1/3 for access; use notches to prevent bottle falls.
Tilt shelves to remove or insert them onto support brackets.
Warning: Door is heavy, get assistance to avoid injury during reversal.
Diagrams illustrating the process of reversing the door on V30 models.
Detailed steps for removing and reattaching door hinges and leg for V30 models.
Steps to remove door axis and door for V40 models with 30mm plinth.
Procedure for removing and reattaching the top hinge for V40 models.
Steps to remove lower and upper hinges for V40 models with 85mm plinth.
Procedure for reattaching the door and hinges for V40 models.
Steps to remove door axis and the door itself for V50 models.
Procedure for installing left hinges and reattaching the door axes.
V30 models are strictly free-standing; built-in voids warranty.
Details dimensions, clearances, venting, and power for V40 85mm recess installation.
Front, side, and top views with dimensions for V40 models (30mm & 85mm).
Specifies dimensions and integration limitations for V50 models.
Further details on clearances, front venting, power requirements for V40 built-in.
Final set of dimensions provided for unit visualization.
Guidance on what to do if the wine cellar malfunctions or loses power.
Advice on protecting wine during power interruptions and restart procedures.
Checks for power, fuse, or appliance being off.
Troubleshooting temperature settings, door seal, and external factors.
Addresses frequent on/off cycles, light not working, and causes.
Diagnosing noise sources and reasons for door not closing properly.
Table detailing capacity, gas load, temperature, dimensions, and weight for R134a models.
Details compressor type, voltage, frequency, defrost, humidity, and lighting.
Highlights double glass door, adjustable feet, and finish options.
Table detailing capacity, gas load, temperature, dimensions, and weight for R600a models.
Information on R600A being environmentally friendly but flammable.
Recommendations for safe transport, installation, and avoiding ignition sources.
Emphasizes authorized service personnel and proper appliance disposal.
To Next Page
