14
Cancelling the selected cooking program
– To cancel the selected cooking program
during the program setting, press the but-
ton (14) once, the multicooker will switch to
the standby mode; then resume selecting
the cooking program by pressing the button
(15) “MENU”.
– To cancel the selected cooking program
during the program operation, press the
button (14) once, you will hear a long
sound signal and the multicooker will be
switched off.
End of cooking program
– After the cooking program ends, you will
hear 10 short sound signals, the digital sym-
bols «0:00» will appear on the display (13).
– Depending on the selected cooking pro-
gram, the unit will be switched to the keep
warm mode automatically, the keep warm
function indicator in the button (14) will
light up.
– To end the cooking program, press the but-
ton (14) once, you will hear a long sound sig-
nal and the multicooker will be switched off.
Keep warm function
– Upon completion of certain cooking pro-
grams the multicooker will switch to the
keep warm mode automatically, the digital
indications «0:00» will appear on the display
(13) and the keep warm indicator in the but-
ton (14) will light up.
– The keep warm function operation time
will be shown in digital symbols on the dis-
play (13).
– The keep warm function maximal operation
time is 12 hours.
– The keep warm function temperature is
65-80°C.
– To switch the keep warm function off, press
the button (14) once, you will hear a long
sound signal and the multicooker will be
switched off.
Note:
– despite the unit keeps the ready dish warm
up to 12 hours, it is not recommended to
leave the cooked food in the multicooker
bowl for a long time, because this may spoil
the food.
– the keep warm function is available for all
cooking programs except “Roasting”.
Delayed start function
Use this function if you want to delay the cook-
ing start for certain time.
– To set the delayed start time, press the but-
ton (17) in the standby mode, the delayed
start time flashing digital symbols will
appear on the display (13) (30 minutes by
default) and the delayed start indicator in
the button (17) will light up.
– Set the required delayed start time by press-
ing the buttons (16) «-», «+» (the possible
setting time is 0.5 –15 hours).
– After setting the delayed start time press the
button (15) “MENU” to select the cooking
program; after 10 seconds the delayed start
time flashing digital symbols will stop flash-
ing and will glow constantly, the countdown
of the set time will start and the indicator in
the button (17) will be glowing.
– Once the delayed start time is over, the mul-
ticooker will switch on and the set cooking
program will start.
– To switch the delayed start function off
press the button (14) once, you will hear a
long sound signal and the multicooker will
be switched off.
Note: - the delayed start function is not avail-
able for «Roasting» and «Baking» programs.
CLEANING AND CARE
• Unplug the unit and let it cool down.
• As the drip container (7) is filled up, remove
the container and pour the accumulated liq-
uid out of it.
• Remove the steam valve (6) from the lid (3)
by pulling it upwards.
• Disassemble the steam valve (6), take the
valve (6) by the bottom part with one hand
and turn the upper part of the valve counter-
clockwise with the other.
• Wash the valve (6), with warm water and
neutral detergent, dry it, then assemble the
valve (6) and install it into the lid (3).
• Clean the unit body (1) and lid (3) with a
slightly damp cloth, and then wipe them dry.
• Wipe the lid (3) from the inside, pay special
attention to the silicone gasket, if the gas-
ket is damaged, stop using the multicooker
and apply to the service center to replace
the gasket.
• Wash the bowl (9), the steam cooking bas-
ket (10), the measuring cup (11) and the
To Next Page
Loading...
