Vivotek MS8391-EV - Page 173

VIVOTEK
User's Manual - 173
URL Command Document for All Series391
37
7.12 Time Shift settings
Group: timeshift, c for n channel products, m is stream number
NAME
VA L U E
DEFAULT
SECURITY
(get/set)
DESCRIPTION
enable
<boolean>
0
4/4
Enable time shift streaming.
c<0~(n-1)>_s<0~(m-1)>_al
low
<boolean>
<product
dependent>
4/4
Enable time shift streaming for
specific stream.
7.13 Motion detection settings
Group: motion_c<0~(n-1)> for n channel product
NAME
VA L U E
DEFAULT
SECURITY
(get/set)
DESCRIPTION
enable
<boolean>
0
4/4
Enable motion detection.
win_i<0~4>_enable
<boolean>
0
4/4
Enable motion window 1~5.
win_i<0~4>_name
string[14]
<blank>
4/4
Name of motion window 1~5.
win_i<0~4>_left
0 ~ 480
0
4/4
Left coordinate of window
position.
win_i<0~4>_top
0 ~ 180
0
4/4
Top coordinate of window
position.
win_i<0~4>_width
0 ~ 480
0
4/4
Width of motion detection
window.
win_i<0~4>_height
0 ~ 180
0
4/4
Height of motion detection
window.
win_i<0~4>_objsize
0 ~ 100
0
4/4
Percent of motion detection
window.
win_i<0~4>_sensitivity
0 ~ 100
0
4/4
Sensitivity of motion detection
window.
Group: motion_c<0~(n-1)> profile for m profile and n channel product (capability.nmotionprofile >
0)
NAME
VA L U E
DEFAULT
SECURITY
(get/set)
DESCRIPTION
i<0~(m-1)>_enable
<boolean>
0
4/4
Enable profile 1 ~ (m-1).
i<0~(m-1)>_policy
day,
night,
schedule
night
4/4
The mode which the profile
is applied to.
URL Command Document for All Series391
38
i<0~(m-1)>_begintime hh:mm 18:00 4/4 Begin time of schedule
mode.
i<0~(m-1)>_endtime hh:mm 06:00 4/4 End time of schedule mode.
i<0~(m-1)>_win_i<0~4>_enable <boolean> 0 4/4 Enable motion window.
i<0~(m-1)>_win_i<0~4>_name string[14] <blank> 4/4 Name of motion window.
i<0~(m-1)>_win_i<0~4>_left 0 ~ 480 0 4/4 Left coordinate of window
position.
i<0~(m-1)>_win_i<0~4>_top 0 ~ 180 0 4/4 Top coordinate of window
position.
i<0~(m-1)>_win_i<0~4>_width 0 ~ 480 0 4/4 Width of motion detection
window.
i<0~(m-1)>_win_i<0~4>_height 0 ~ 180 0 4/4 Height of motion detection
window.
i<0~(m-1)>_win_i<0~4>_objsize 0 ~ 100 0 4/4 Percent of motion detection
window.
i<0~(m-1)>_win_i<0~4>_sensitiv
ity
0 ~ 100 0 4/4 Sensitivity of motion
detection window.
7.14 Tampering detection settings
Group: tampering_c<0~(n-1)> for n channel product
NAME VA L U E DEFAULT SECURITY
(get/set)
DESCRIPTION
enable <boolean> 0 4/4 Enable or disable tamper detection.
duration 10 ~ 600 10 4/4 If tampering value exceeds the ‘threshold’ for
more than ‘duration’ second(s), then tamper
detection is triggered.