ViziT KTM600F - Operation; Specifications

Lost keys erasing
All keys erasing
PRG
PRG
OPERATION
ACCESS mode
GUARD mode
N
SPECIFICATIONS
0
1
1 or 7 sec
VDC
mA
1.5 at 24 VDC
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
Move the close to ’s antenna and hold it
are ing
Approach ’s antenna 300M The
Approach to the reader’s antenna, from the
memory
When done, approach to the reader’s antenna, the system will return the .
Take off cover from the Control Unit, remove
is ing
300M are ing the is illuminating: t is ing
and hold 300M before beeps stop Two short beeps
are sounding. When done, a is ing
put cover back
will the
g
the ’s is
antenna ’s code
C U ’s are ing , ’s is ing
’s code found is ing
300M
Move close ’s antenna are ing the is ing
the D not available
When the GUARD mode is on, a regular to the reader
Approach once more to the reader’s antenna the . T
are ing The MASTER-key may be used as well to switch the GUARD mode off.
A does not function as , it cannot
The GUARD mode does not block t , and it may from inside of the building
300M , with OPEN from
F,
MASTER-key the reader for 5 seconds at least. The lock is released, short beeps
and three long beeps sound . Take the MASTER-key off before the third long beep ends.
the MASTER-key briefly to the reader , then press the EXIT button twice. LED shuts off.
the key with previous number (N-1) and the lost key (number N) is erased
.
the MASTER-key briefly to ACCESS mode
The following sequence of operations results in erasing of all keys, including the MASTER-key!
Turn the power off.
the and the jumper.
Turn the power on.Along beep sound .
Press the EXIT button. Twenty short beeps sound , LED he system wait for
confirmation. To confirm, press the EXIT button for 2 seconds the .
long beep sound .
Turn the power off, restore the jumper to its place and the .
In 30 – 50 seconds of idle the system return to ACCESS mode.
One of the following operatin modes is available:
ACCESS mode
GUARD mode
The door is locked in stand-by mode. The .
To unlock the door, an ACCESS (MASTER)-key to the If the key is stored in the
ontrol nit memory, the lock releases, short beeps sound for 7 seconds and the LED illuminat .
If the key is not , then the door remains locked and a long beep sound .
To unlock the door from inside of the building, press the EXIT button.
a GUARD key to the reader . One short and one long beeps sound , LED illuminat ,
the system goes to GUARD mode. oor unlocking with ACCESS keys is in this mode.
pplying a ACCESS key results in a long beep.
a GUARD key to return to ACCESS mode wo short and one long
beeps sound .
GUARD key an access key unlock the door.
he lock be released by pressing the
EXIT button or DOOR button a subscriber device.
ACCESS keys, max.
GUARD keys, max.
MASTER-key
Unlocked state duration
Operating voltage
VIZIT-KTM600 current consumption max.
Max. switchable current
IMPORTANT.
Note.
ote 1.
Note 2.
268 pcs.
28 pcs.
pc.
onds
12 ... 28
60
A
.
C U ing
approach close ’s
CU
ontrol nit LED blink
reader
ontrol nit
PART
Control Unit
Reader
Temperature
range
+1°C +40°Cup to
- 0°C +50°C3 up to
Humidity of air
up to at93% 25°C
up to at98% 25°C
Dimensions,
mm
75x135x35
47x75x18
Weight, kg
0.2
0.1
www. 5VIZIT-KTM600F Operating Instruction (revision 10)vizit-group.com 11 11/201 -