VLT FC 300 - Page 107

P
PELV................................................................................................. 2-7, 6-1
Phase Loss.............................................................................................. 8-2
Power
Connections..................................................................................... 2-5
Factor................................................................................. 1-4, 2-6, 3-2
Power-dependent............................................................................ 10-1
Pre-start.................................................................................................. 3-1
Programming
Programming... 1-2, 2-10, 3-7, 4-2, 5-3, 5-4, 5-9, 8-2, 3-3, 4-1,
4-3, 5- 0
Example............................................................................................. 5-1
Pulse/Encoder Inputs.................................................................... 10-16
Q
Quick
Menu.................................................................................. 5-1, 5-3, 4-2
Set-up................................................................................................. 3-3
R
Ramp-down Time............................................................................... 3-7
Ramp-up Time...................................................................................... 3-7
RCD........................................................................................................... 2-6
Reference............................................................................. 0-iii, 6-1, 4-2
Relay Outputs.......................................................................... 2-8, 10-17
Remote
Commands........................................................................................ 1-3
Programming................................................................................... 5-9
Reference........................................................................................... 7-1
Reset.............................................................. 4-1, 4-4, 7-1, 8-2, 8-8, 4-3
RFI Filter.................................................................................................. 2-7
RMS Current.......................................................................................... 1-4
Run
Command......................................................................................... 3-7
Permissive......................................................................................... 7-1
S
Safe Stop.............................................................................................. 2-12
Safety Inspection................................................................................. 3-1
Serial Communication.......... 1-3, 2-8, 2-10, 4-3, 7-1, 2-12, 10-17
Setpoint.................................................................................................. 7-1
Set-up.............................................................................................. 3-7, 4-2
Shielded
Cable.................................................................................. 2-1, 2-5, 3-2
Control Cables............................................................................... 2-10
Wire..................................................................................................... 2-5
Short Circuit.......................................................................................... 8-4
Smart Application Set-up (SAS)..................................................... 3-3
Specifications.................................................................. 1-2, 2-12, 10-1
Speed Reference...................................................... 2-11, 3-7, 5-2, 7-1
Start Up................................................................................................... 9-1
Startup.................................................................................................... 1-2
Start-up............................................................................ 4-4, 5-1, 3- 0
Status
Messages........................................................................................... 7-1
Mode................................................................................................... 7-1
Stop Command.................................................................................... 7-1
Supply Voltage........................................................... 2-7, 2-8, 3-1, 8-5
Switching Frequency......................................................................... 7-1
Symbols................................................................................................. 0-iii
System
Feedback........................................................................................... 1-3
Monitoring........................................................................................ 8-1
Start-up.............................................................................................. 3-7
T
Technical Data................................................................................. 10-14
Temperature Limits............................................................................ 3-2
Terminal
53...................................................................................... 5-1, 2-11, 5-1
54....................................................................................................... 2-11
Programming................................................................................ 2-10
Programming Examples............................................................... 5-2
Thermistor
Thermistor........................................................................ 2-7, 8-3, 6-1
Control Wiring................................................................................. 2-7
Tightening Of Terminals.............................................................. 10-28
Torque
Characteristics............................................................................ 10-14
Limit..................................................................................................... 3-7
Transient Protection.......................................................................... 1-4
Trip
Trip....................................................................................................... 8-1
Function............................................................................................. 2-5
Lock..................................................................................................... 8-1
Troubleshooting................................................................... 1-2, 9- 0
U
Uploading Data To The LCP............................................................ 4-4
V
Voltage
Imbalance.......................................................................................... 8-2
Level............................................................................................... 10-14
Index
VLT
®
AutomationDrive Instruction
Manual
MG33AM22 - VLT
®
is a registered Danfoss trademark 12-3