VLT FC 300 - Page 106

Full Load Current................................................................................. 2-1
Functional Testing....................................................... 1-2, 3-7, 3- 0
Fuses.......................................................................... 3-2, 8-5, 9-1, 10-19
Fusing............................................................................................. 2-5, 3-2
G
Ground
Connections............................................................................. 2-6, 3-2
Loops................................................................................................ 2-10
Wire............................................................................................. 2-6, 3-2
Grounded Delta................................................................................... 2-7
Grounding
Grounding............................................................... 2-6, 2-7, 3-1, 3-2
Using Shielded Cable.................................................................... 2-6
H
Hand
Hand........................................................................................... 4-3, 7-1
On........................................................................................ 3-7, 7-1, 4-3
Harmonics.............................................................................................. 1-4
I
IEC 61800-3............................................................................................ 2-7
Induced Voltage.................................................................................. 2-5
Initialization........................................................................................... 4-4
Input
Current............................................................................................... 2-7
Disconnect........................................................................................ 2-7
Power............................................... 2-5, 2-6, 2-7, 3-1, 3-2, 8-1, 1-4
Signal.................................................................................................. 5-2
Signals................................................................................... 2-10, 2-11
Terminal............................................................................................. 8-2
Terminals........................................................................ 2-3, 2-11, 3-1
Voltage....................................................................................... 3-3, 8-1
Installation............................... 1-2, 2-1, 2-2, 2-5, 2-9, 2-12, 3-2, 3-3
Isolated Line Power............................................................................ 2-7
L
Leakage Current.......................................................................... 3-1, 2-6
Lifting...................................................................................................... 2-2
Line
Power.................................................................................................. 2-5
Power Supply........................................................... 10-1, 10-8, 10-9
Power Supply (L1, L2, L3)........................................................ 10-14
Supply.............................................................................................. 10-7
Local
Control............................................................................... 4-1, 4-3, 7-1
Control Panel................................................................................... 4-1
Control Test...................................................................................... 3-7
Mode................................................................................................... 3-7
Operation.......................................................................................... 4-1
Start..................................................................................................... 3-7
M
Main Menu............................................................................ 4-2, 5-1, 4-2
Manual Initialization.......................................................................... 4-4
MCT 10 Set-up Software Set-up Software.................................. 5-9
Mechanical Brake Control.............................................................. 2-11
Menu
Keys............................................................................................. 4-1, 4-2
Structure.................................................................................... 4-3, 5-4
Modbus RTU....................................................................................... 2-12
Motor
Cables................................................................................ 2-1, 2-5, 2-6
Current...................................................................... 1-4, 3-5, 8-7, 4-2
Data........................................................... 3-3, 3-4, 3-7, 8-3, 8-7, 3-6
Output........................................................................................... 10-14
Power......................................................................... 2-3, 2-5, 2-6, 8-7
Protection.......................................................................................... 2-5
Rotation..................................................................................... 3-6, 4-2
Speeds................................................................................................ 3-3
Status.................................................................................................. 1-3
Wiring................................................................................ 2-5, 2-6, 3-2
Mounting............................................................................................... 2-2
Multiple
Adjustable Frequency Drives............................................. 2-5, 2-6
Motors................................................................................................ 3-1
N
Navigation Keys.................................................................. 3-3, 5-1, 4-3
Noise Isolation............................................................................. 2-5, 3-2
O
Open-loop.................................................................................. 2-11, 5-1
Operation Keys..................................................................................... 4-3
Optional Equipment....................................................... 2-7, 2-11, 3-3
Output
Current....................................................................................... 7-1, 8-3
Performance (U, V, W).............................................................. 10-14
Signal.................................................................................................. 5-4
Terminals................................................................................... 2-3, 3-1
Overcurrent........................................................................................... 7-1
Overload Protection.................................................................. 2-1, 2-5
Overvoltage.................................................................................. 3-7, 7-1
Index
VLT
®
AutomationDrive Instruction
Manual
12-2 MG33AM22 - VLT
®
is a registered Danfoss trademark