What does Error Code FF:12 mean on my VMAI V8 Pro Ultrasonic Jewelry Cleaner?
If your VMAI Ultrasonic Jewelry Cleaner displays Error Code FF:12, it indicates that no dirty water tank is installed. Install the dirty water tank.
Why is the vacuum on my VMAI V8 Pro Ultrasonic Jewelry Cleaner getting weaker?
If the vacuum of your VMAI Ultrasonic Jewelry Cleaner is getting weaker, the HEPA filter might be blocked. Please check and clean the HEPA filter. Also, the HEPA filter might be wet, so ensure it is dry before use. Finally, check if the scraper is properly installed and reinstall it if necessary.
Why does my VMAI Ultrasonic Jewelry Cleaner have no voice assistance?
If your VMAI Ultrasonic Jewelry Cleaner has no voice assistance, ensure that the voice function is turned on. If it's already on, your version might not include voice assistance; please check with your local seller.
How to calibrate the clean water tank indicator on my VMAI V8 Pro?
If the indicator display of the clean water tank on your VMAI Ultrasonic Jewelry Cleaner is incorrect, the device might be uncalibrated. Remove the Clean Water tank, then start to clean and spray, turn cleaner off until draining the pipe. Then press the “Switch Button” and “Eco/Max Button “for 5 seconds until the digital display flashes two times, then check again.
Why does my VMAI V8 Pro move so hard?
If your VMAI Ultrasonic Jewelry Cleaner moves hard, the roller brush might not be installed correctly. Please check and reinstall the roller brush as guided.
Why are there water drops at the air outlet of my VMAI V8 Pro Ultrasonic Jewelry Cleaner?
If you see water drops at the air outlet of your VMAI Ultrasonic Jewelry Cleaner, ensure the HEPA filter is installed correctly. Also, make sure you're using the machine correctly and not tilting it too much. If you're vacuuming foam liquid, empty the dirty water tank promptly.
How to fix VMAI V8 Pro Ultrasonic Jewelry Cleaner that won't charge?
If your VMAI Ultrasonic Jewelry Cleaner cannot be charged, check the connection of the power supply to ensure it is well connected. Also, try replacing the cleaner on the charging station to ensure it's properly connected.
Why doesn’t the handle control work on my VMAI V8 Pro Ultrasonic Jewelry Cleaner?
If your VMAI Ultrasonic Jewelry Cleaner handle control isn’t working, the battery capacity might be low. Please check the battery capacity and fully charge it. Another reason could be that the handle isn’t connected properly, so try reinstalling it.
Why is the clean water tank leaking on my VMAI Ultrasonic Jewelry Cleaner?
If the clean water tank of your VMAI Ultrasonic Jewelry Cleaner is leaking, it could be because the water volume is higher than the snuffle valve. Pour out water until it's below the snuffle valve. Also, make sure the clean water tank is installed correctly; reinstall it if necessary. Finally, ensure that the cap is screwed on tightly.
Why doesn't my VMAI V8 Pro work in self-cleaning mode?
If your VMAI Ultrasonic Jewelry Cleaner doesn't work in self-cleaning mode, ensure that it's properly connected to the power supply. Also, check if the dirty water tank is full and empty it if needed. Lack of water can also be the cause, so fill up the clean water tank.
Diagram showing the front view of the cleaner with labeled parts.
Diagram showing the back view of the cleaner with labeled parts.
Diagram of the clean water tank with labeled components.
Diagram of the brush base with labeled parts.
Diagram of the charging station with labeled parts.
Explains indicators for Eco/Max modes and working time.
Indicates low clean water or full dirty water tank.
Shows self-cleaning mode and remaining battery capacity.
Instructions for charging the cleaner and its battery pack.
Steps for using the cleaner to clean floors.
Details on using switch, max mode, spray button, and priming.
Guidance on handle tilt, cleaning motion, and rug warnings.
Instructions for cleaning the dirty water tank after use.
Steps to perform automatic self-cleaning of the roller brush and pipeline.
Guidance on wiping the main body, station, and brush base.
Instructions for removing and cleaning the roller brush.
Steps for emptying and cleaning the dirty water tank and HEPA filter.
Instructions for cleaning the charging station and drying tray.
Guidance on drying and storing machine parts and battery pack.
Information on how to get assistance or report problems.
General| Brand | VMAI |
|---|---|
| Model | V8 Pro |
| Category | Ultrasonic Jewelry Cleaner |
| Language | English |
To Next Page