EasyManua.ls Logo

Voltech BC- 1260P User Manual

Default Icon
12 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
BC-1230P/ 1240P/ 1260P
Multi-Stage Battery Chargers
User Manual
Keep this manual in a safe place for quick reference at all times.
This manual contains important safety and operation instructions for correct use of the battery charger. Read through the manual
And pay special attention to the markings and labels of the charger, battery and any equipment connected into the system.
Pay special attention to these two types of notices used in this manual;
WARNING:
Failure to heed this warning may cause injury to persons and damage to Equipment.
CAUTION:
Failure to observe this warning may result in damage to equipment and improper functioning of the Charger.
WARNING:
The charger is designed for in-door use. Protect the charger from ingress of water.
This charger is made to charge only properly sized lead acid batteries.
Don't recharging non-rechargeable batteries.
Charging other types of battery or under-sized lead acid batteries may cause fire or explosion.
Install the charger in accordance with all local codes
Do not use the charger if it has been dropped or damaged.
Do not remove casing of the charger, there is no user serviceable parts inside.
Never attempt to charge a frozen battery
Never attempt to charge a damaged battery.
Wear protective goggles and turn your face away when connecting or disconnecting the battery.
Never place the charger on top of a battery.
Never smoke, use an open flame, or create sparks near battery or charger during normal charging operation as Batteries may
give out explosive gas.
Do not charge batteries in a sealed enclosure (boxed- in) due to possible explosion of entrapped explosive gas.
Use of accessories not recommended may cause risk of fire, electric shock or equipment damage.
Disconnect the mains supply before connecting or disconnecting the links to the battery.
If the charger does not work properly or if it has been damaged, unplug its AC and DC connection.
Do not use this charger in connection with any medical device or life support system.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Battery chargers for charging automobile batteries shall not be fitted with natural rubber-sheathed supply cords.
CAUTIONS:
Refer to battery manufacturer’s specific recommended values for battery type settings and float voltage setting.
Ensure all ventilation ports are not obstructed for efficient fan cooling, keep loose soft material such as paper, cloth, etc. away
from the Charger
During charging, the battery must be placed in a well ventilated area.
If longer output charging cable are required, make sure the cable diameter is adequate for the Current & Cable length.
AC source from portable generator:
The VA rating of a standard generator should be at least 4 times the maximum rating of the charger.
How-ever, Inverter type generators need to have only 2 to 3 times the maximum rating of the charger.
It is recommended that the ac output is stabilized by running the generator for 2-3 minutes before switching on the charger.
This charger is for standalone application only, parallel or series connection with another charger may cause damage to charger
and connected battery.
AC supply cord (leads) should be at least minimum size of 3G 0.75mm
2
nominal cross-sectional area.
Question and Answer IconNeed help?

Do you have a question about the Voltech BC- 1260P and is the answer not in the manual?

Voltech BC- 1260P Specifications

General IconGeneral
BrandVoltech
ModelBC- 1260P
CategoryBattery Charger
LanguageEnglish

Summary

A. Control and Indicators

Battery Connection Terminals

Terminals for connecting the battery and DC output.

Selecting Battery Type

Guides on selecting the correct battery type for charging.

B. Using the charger

C. Power Level adjustment

E. Battery Charger Installation and Connection

F. Normal 4-Stage (IUoU) Charging Operation

Bulk Charge Mode (Stage 1)

Constant current charging phase.

Absorption Charge Mode (Stage 2)

Constant voltage charging phase.

Float Charge Mode (Stage 3)

Maintaining charge level.

Standby Charge Mode (Stage 4)

Reduced voltage for inactive batteries.

H. User-Defined Charging Profiles

I. Wet Battery Equalization Charging

J. Dual Bank Charging Feature

K. Temperature Sensor Operation

M. Protection and Fault Indications

Charger Overheat Protection (OTP)

Protection activated when charger overheats.

Fan Malfunction Fault

Indicates fan is not working or stuck.

Output Over Voltage Protection (OVP)

Protects battery and load from over-voltage.

Overload/Over Current Protection

Protects the charger from excessive current.

Short Circuit Protection

Indicates a short circuit condition.

Reverse Polarity Protection

Protection against incorrect battery polarity connection.

N. Troubleshooting (No Remote Display)

Troubleshooting: Charger Not Working

Troubleshooting steps for when the charger has no power.

Troubleshooting: No DC Output

Diagnosing issues when the charger is on but provides no output.

Troubleshooting: Incomplete Battery Charge

Solutions for incomplete battery charging.

Troubleshooting: Extended Charge Time

Addressing extended charging times without reaching float stage.

O. Technical Specifications

P. Optional Remote Display (HBR-3100)

Remote Display Fault Code Explanations

Lists and explains various fault codes displayed on the remote.

Related product manuals