What does it mean if Wacker Neuson Power Tool receiver units flash red?
If the receiver units flash red on the Wacker Neuson Power Tool, it means the machine is overloaded because the soil cannot be compacted any further. To resolve this: * Avoid operation on non-compactable soil. * Reduce the compaction performance by actuating the slow / fast rocker switch. * Switch over from fast to slow operation.
What does it mean if Wacker Neuson Power Tool receiver units light up red?
If the receiver units light up red on your Wacker Neuson Power Tool, it could indicate that the machine is in the warm-up phase. Wait until the warm-up phase has completed. It may also indicate that the diagnostic system has detected an error. Check control lamps and fault indications on the display.
Why Wacker Neuson Power Tool engine smokes and does not perform?
If the Wacker Neuson Power Tool engine smokes and does not perform well, it could be due to a dirty air cleaner. Replace the air cleaner.
What to do if Wacker Neuson Power Tool receiver units flash yellow rapidly and the machine does not respond?
If the receiver units flash yellow in rapid succession and the Wacker Neuson Power Tool does not respond to commands from the remote control, it could be because the operator is located in the proximity area. Leave the proximity area of the machine.
What to do if Wacker Neuson Power Tool engine runs unevenly?
If the engine of your Wacker Neuson Power Tool runs unevenly, the possible causes include: * A dirty fuel filter. Replace the fuel filter. * A dirty air cleaner. Clean or replace the air cleaner.
What to do if Wacker Neuson Power Tool machine cannot be activated?
If the Wacker Neuson Power Tool machine cannot be activated, it might be due to: * An incorrect activation PIN being entered. Enter the correct activation PIN. * A defective electrical system. Deactivate the machine with the emergency stop switch.
What to do if Wacker Neuson Power Tool receiver units light up yellow and the machine does not respond?
If the receiver units light up yellow and the Wacker Neuson Power Tool does not respond to remote control commands, check these possible causes: * Ensure the remote control is switched on. * The rechargeable battery of the remote control may be discharged; load or replace it. * Make sure you are within the receiving area of the machine. * Establish a clear line of sight between the remote control and the receiver unit. * Clean the remote control and receiving units if they are dirty. * The remote control is defective.
General| Model | DPU110 Series |
|---|---|
| Category | Power Tool |
| Centrifugal Force | 110 kN |
| Working Width | 800 mm |
| Frequency | 32 Hz |
| Engine Power | 15.9 hp (11.9 kW) |
Know regulations, conduct risk assessments, create operating instructions, train staff.
Residual dangers exist despite safe design; stop operation if unforeseeable dangers occur.
Crucial safety guidelines applicable to machine operation.
Machine specific safety for vibratory plates.
Direct operation safety: safety during operation (lines, slopes, unattended machines, distance).
Machine specific safety for remote controlled plates.
Engine specific safety: engine checks, fuel handling, exhaust fumes, hot surfaces.
Fluid safety: handling fuel, lubricants, coolants; eye protection, skin contact, ingestion.
Battery safety: battery connection/disconnection, acid handling, short circuit prevention.
Specific safety feature: machine shuts off vibration/movement in specific situations.
Emergency response: preventive measures and emergency actions.
Control lamps and display: explains display and control lamps (operation, charging, preheating, etc.).
Remote controls: identifies controls on the remote unit (joystick, socket, strap, battery, buttons, lamps).
Initial setup: opening hoods and performing pre-operation checks.
Key operational warnings: warnings about tipping, exhaust fumes, and operation on slopes.
Starting the machine: steps to activate the machine using the ON/OFF switch.
General operation: general operation instructions.
Center pole controls: controls for center pole operation (vibration, direction, speed).
Remote control operation: how joysticks control machine movement and speed.
Shutting down: steps to turn off the machine.
Emergency stop procedure: using the emergency stop switch.
Scheduled maintenance: maintenance tasks at specific intervals (125h, 250h, 500h).
Engine oil: checking and refilling engine oil.
Oil change: procedure for changing engine oil and oil filter.
Coolant check: checking and topping off coolant in the reservoir and radiator.
Hydraulic oil: checking and refilling hydraulic oil.
Machine faults: lists common machine faults and their remedies.
Display/lamp faults: faults indicated by control lamps and display messages.
To Next Page