Why won't the motor start on my Wacker Neuson DPU 6555?
If the motor of your Wacker Neuson Power Tool won't start, it could be due to several reasons. It might be a defective ignition lock, in which case you should have the machine repaired. Another potential cause is a discharged starter battery, so try charging the starter battery. Also, check the oil level; if it's low, top up the oil and actuate the valve hood on the oil filter housing.
What to do if the charge control lamp won't go out on my Wacker Neuson Power Tool?
If the charge control lamp on your Wacker Neuson Power Tool doesn't turn off and the acoustic signal keeps sounding, it could be due to a defective alternator. In this case, you should have the machine repaired.
Why won't my Wacker Neuson Power Tool engine start?
Several factors can prevent your Wacker Neuson Power Tool engine from starting. It could be due to a defective ignition lock, requiring professional repair. Another reason might be a discharged starter battery, which you can resolve by charging it. Low oil level can also be the cause; in this case, add oil and actuate the valve lever on the oil filter housing once.
What to do if charge indicator light does not go out on Wacker Neuson Power Tool?
If the charge indicator light on your Wacker Neuson Power Tool doesn't turn off and the switch cannot be silenced, it could be due to an alternator failure, which requires professional repair.
Why is the forward travel speed too low on my Wacker Neuson DPU 6555?
If the forward travel speed of your Wacker Neuson Power Tool is too low, it may be caused by too much hydraulic oil in the center pole head. Correct the oil level accordingly. Another possible cause is air in the hydraulic control system, so bleed the system.
What to do if all LEDs are flashing on the Wacker Neuson DPU 6555 Power Tool compaction display?
If all LEDs on the compaction display of your Wacker Neuson Power Tool are permanently flashing after initialization, the sensor might not have been successfully tested. This could be due to switching on the machine with the engine running, in which case you should have the machine repaired.
How to fix low reverse travel speed on Wacker Neuson DPU 6555 Power Tool?
If the reverse travel speed of your Wacker Neuson Power Tool is too low, it could be due to not enough hydraulic oil in the center pole head. To solve this, top off the hydraulic oil.
Why am I losing hydraulic oil from my Wacker Neuson DPU 6555?
If you notice a loss of hydraulic oil in your Wacker Neuson Power Tool, it's likely due to leaks. You should have the machine repaired to address this issue.
What causes no travel speed on a Wacker Neuson Power Tool?
If there is no travel speed on your Wacker Neuson Power Tool, it indicates a mechanical fault. You should have the machine repaired.
What to do if my Wacker Neuson Power Tool forward speed is too low?
If the forward speed of your Wacker Neuson Power Tool is too low, it might be due to too much hydraulic oil in the centre pole head. Correct the oil level accordingly. Alternatively, there might be air in the hydraulic control system, which requires bleeding.
Defines the legal and operational responsibilities of the machine operator.
Lists the duties of the operator regarding safety, training, and compliance.
Safety measures to ensure safe operation of the machine.
Safety instructions for operating and refueling the machine's combustion engine.
General safety instructions to be followed during maintenance.
Details on required personal protective equipment for safe operation.
Provides guidance on preventive measures and actions during emergencies.
Identifies and describes the machine's operating controls and displays.
Details on dangers of falling machines and safe lifting procedures.
Instructions for attaching lifting tackle and tying down the machine for transport.
Essential checks to perform on the engine and components before starting.
Step-by-step guide for starting the machine using the manual crank.
Detailed steps and notes for using the starting crank effectively.
Instructions for starting the machine using the electric starter.
Warnings related to improper handling, exhaust fumes, and hot surfaces during maintenance.
A table detailing maintenance tasks, frequencies, and intervals.
Safety warnings and steps for changing the starter battery.
Steps for correctly installing and connecting a new starter battery.
Lists common faults, their possible causes, and remedial measures.
Procedure for jump-starting the machine using another vehicle's battery.
Detailed steps for connecting and disconnecting jumper cables for jump starting.
Detailed specifications for DPU 4545H, 4545He, and 4545Heh models.
Vibration and sound power level data for DPU 4545 models.
Specifications for DPU 4545Hec and 4545Hech US models.
Vibration and sound data for DPU 4545 US models.
Detailed specifications for DPU 5545H, 5545He, 5545Heh, 5545Heap models.
Vibration and sound power level data for DPU 5545 models.
Specifications for DPU 5545Hec and 5545Hech US models.
Vibration and sound data for DPU 5545 US models.
Technical details for Hatz engine models used in the vibratory plates.
General| Centrifugal Force | 65 kN |
|---|---|
| Base Plate Length | 900 mm |
| Engine Type | Diesel |
| Engine Manufacturer | Hatz |
| Engine Model | 1D81Z |
| Frequency | 69 Hz |
| Travel Speed | 28 m/min |
| Engine Power | 9.7 kW |
To Next Page