WAGNER Power Painter Max User Manual (English)

Questions and Answers:

D
Donald SmithAug 14, 2025
What to do if my WAGNER Paint Sprayer is spitting paint?
- R
  Rebecca PattersonAug 14, 2025
  If your WAGNER Paint Sprayer is spitting or globbing material, it indicates air has entered the system. Here's what you can do: * Refill the paint container if it's low. * If equipped, increase the speed setting. * Ensure the material selector is set to “PAINT”. * Clean and lubricate the O-rings on the filter assembly. * Thin the material if it's too thick. * Clean the spray tip. * Replace the atomizer valve if it is worn. * Clean and oil, or replace the piston if it's worn.
J
johnadkinsAug 17, 2025
Why is my WAGNER Power Painter Max Paint Sprayer leaking from the spray tip?
- L
  Lonnie LynchAug 17, 2025
  If material is leaking from between the spray tip and locking nut of your WAGNER Paint Sprayer, try these steps: 1. Ensure the spray tip is securely tightened. 2. Unplug the sprayer, remove the spray tip, and reposition the atomizer valve. 3. Replace the atomizer valve if it's worn. 4. Replace the pump housing if it's eroded.
T
Tony HaneyAug 20, 2025
Why WAGNER Power Painter Max Paint Sprayer motor runs but does not spray?
- O
  ojamesAug 21, 2025
  If your WAGNER Paint Sprayer motor operates properly but doesn't spray, several factors could be at play. Try the following: * Ensure you've oiled the intake opening. * If using a remote suction set, hold the trigger for at least 3 minutes, thin the paint, and keep the sprayer level with the paint can during priming. If using a suction tube, hold the trigger for at least 20 seconds and thin the paint. * Tighten or replace a loose or damaged suction tube. * Clean or replace a plugged or worn atomizer valve, or replace it if missing. * Adjust the material selector to the “PAINT” setting. * Increase the speed setting if equipped. * Clean a plugged spray tip or filter assembly. * Thin the material if it's too thick. * Clean and oil, or replace a worn piston.
J
jenniferstewartAug 25, 2025
Why WAGNER Paint Sprayer motor will not run?
- P
  Paul WilliamsAug 25, 2025
  If your WAGNER Paint Sprayer motor will not run, it could be due to an electrical problem or a defective motor. First, try a new wall outlet. If that doesn't work, take the sprayer to an Authorized Service Center for repair.
J
Joshua GoodwinAug 27, 2025
Why does my WAGNER Paint Sprayer hum but not spray?
- M
  Michelle ThorntonAug 27, 2025
  If your WAGNER Paint Sprayer motor has a low hum and does not spray, it may be due to a seized piston. Disassemble the sprayer, then clean and lubricate it, following the Cleanup, Cup Mode instructions.
A
Adam LoveAug 30, 2025
How to reduce fogging with my WAGNER Power Painter Max?
- R
  Randall HermanAug 30, 2025
  Excessive fogging with your WAGNER Paint Sprayer can be due to the material selector being set too high, so set the material selector to ‘stain’. Also, ensure you are holding the sprayer closer to the work surface.
C
Carol FosterSep 3, 2025
Why is my WAGNER Power Painter Max motor overheating?
- C
  Christopher SchultzSep 3, 2025
  If your WAGNER Paint Sprayer motor overheats, clean the piston if it is seized. If you're using an extension cord, replace it with the proper size. Also, release the trigger at the end of a pass and allow the sprayer to cool if operating continuously.
D
David BerrySep 6, 2025
How to prevent runs and sags with WAGNER Paint Sprayer?
- T
  Timothy BrooksSep 7, 2025
  If your WAGNER Paint Sprayer is causing runs and sags in the paint, refer to the spraying section (page 8). This issue typically arises from arm movement being too slow, holding the spray gun too close to the work surface, or applying too much paint at once.
B
Brian MoralesSep 9, 2025
Why is my WAGNER Power Painter Max Paint Sprayer dripping material?
- A
  Ashley JonesSep 10, 2025
  Some dripping from the spray tip or guard of your WAGNER Paint Sprayer is unavoidable with some paints. Use a small brush on drips that fall on the surface being sprayed and use a drop cloth.

WAGNER Power Painter Max Specifications

General

Brand	WAGNER
Model	Power Painter Max
Category	Paint Sprayer
Language	English

Summary

Important Safety Information

Safety Precautions

Covers grounding, fire, injection, general injury, and electrical shock risks.

Important Electrical Information

Before You Begin

Preparation and Material Handling

Covers material prep, thinning, usable/prohibited materials, and job size determination.

Spraying Techniques and Tips

Discusses overspray, drop cloths, spray tip, capabilities, and what not to use.

Sprayer Features

Power Painter Plus Features

Lists features specific to the Power Painter Plus model.

Power Painter Max Features

Lists features specific to the Power Painter Max model.

Power Painter Pro Features

Lists features specific to the Power Painter Pro model.

Cup Mode Setup

Small to Medium Jobs

Indicates suitability of cup mode for specific job sizes.

Avoid Running Cup Dry

Crucial warning about running the cup empty to prevent issues.

Ensure Tip Nut Security

Essential pre-spraying check for tip nut security.

Remote Suction Hose Setup

Medium to Large Jobs

Advises on using remote suction hoses for larger tasks.

Avoid Running Container Dry

Warning against running the material container dry.

Maintain Tip Nut Tightness

Reminder to ensure the tip nut is tight before spraying.

Backpack Kit Setup

Large Jobs with Mobility

Indicates suitability of the backpack kit for large jobs requiring mobility.

Avoid Running Backpack Dry

Warning about not running the backpack empty.

Tip Nut Tightness Check

Pre-spray check for tip nut tightness.

Spray Controls Overview

Power Painter Plus Controls

Details controls for the Power Painter Plus model.

Power Painter Max Controls

Details controls for the Power Painter Max model.

Power Painter Pro Controls

Details controls for the Power Painter Pro model.

Priming with Remote Suction Hoses

Suction Hose Submersion Warning

Critical warning about keeping the suction hose submerged to prevent damage.

Practice Spraying Guide

Preparation and Materials

Lists materials needed and important pre-spraying advice.

Spraying and Priming Techniques

Covers priming the sprayer and managing overspray.

Spraying Techniques

Adjusting Spray Pattern

How to adjust the spray pattern horizontally or vertically.

Leakage Warning

Critical warning about material leakage from the spray tip assembly.

Cleanup - Cup Mode

Cleaning Supplies Required

Lists necessary items for cleaning.

Ventilation During Cleaning

Safety warning regarding ventilation during cleaning with solvents.

Cleanup - Remote/Backpack Kits

Supplies for Remote Cleaning

Lists items required for cleaning remote setups.

Solvent Cleaning Ventilation

Safety warning for cleaning with flammable solvents.

Reassembly and Maintenance

Post-Cleaning Reassembly

Guide on how to reassemble the sprayer after cleaning.

Troubleshooting Common Issues

Motor and Spraying Problems

Solutions for motor not running, low hum, no spray, spitting, or globbing.

Advanced Troubleshooting

Spray Pattern and Leak Issues

Solutions for fogging, runs, sags, drips, and tip/nut leaks.

Motor Overheating Solutions

Addresses causes and solutions for motor overheating.

Replacement Parts Information

Atomizer Valve Replacement

Details on the atomizer valve's function, wear, and replacement.

Piston and Spring Replacement

Information on piston and spring lifespan and replacement.

Parts Identification List

Component Identification

Visual and textual list of all sprayer components.

Repacking Sprayer Components

Fitting Sprayer into Case

Instructions for repacking the sprayer and components into the carrying case.

Wagner Limited Warranty

Spray Tip Lifetime Warranty

Explains the lifetime warranty for the spray tip.

Related product manuals

WAGNER Power Painter Pro

22 pages

WAGNER Power Painter Plus

22 pages

WAGNER PRO DUTY POWER PAINTER

13 pages

WAGNER EZ TILT POWER PAINTER PRO

22 pages $Preview: WAGNER POWER TEX$

WAGNER POWER TEX

20 pages

CONTROL PRO 130 POWER TANK

24 pages

WAGNER Control Painter

40 pages

WAGNER POWERPAINTER 90 EXTRA

156 pages

PowerPainter 90 EXTRA Skid

WAGNER Paint Crew 770

20 pages

WAGNER Power Painter Max User Manual

Table of Contents

Questions and Answers:

WAGNER Power Painter Max Specifications

Summary

Important Safety Information

Safety Precautions

Important Electrical Information

Before You Begin

Preparation and Material Handling

Spraying Techniques and Tips

Sprayer Features

Power Painter Plus Features

Power Painter Max Features

Power Painter Pro Features

Cup Mode Setup

Small to Medium Jobs

Avoid Running Cup Dry

Ensure Tip Nut Security

Remote Suction Hose Setup

Medium to Large Jobs

Avoid Running Container Dry

Maintain Tip Nut Tightness

Backpack Kit Setup

Large Jobs with Mobility

Avoid Running Backpack Dry

Tip Nut Tightness Check

Spray Controls Overview

Power Painter Plus Controls

Power Painter Max Controls

Power Painter Pro Controls

Priming with Remote Suction Hoses

Suction Hose Submersion Warning

Practice Spraying Guide

Preparation and Materials

Spraying and Priming Techniques

Spraying Techniques

Adjusting Spray Pattern

Leakage Warning

Cleanup - Cup Mode

Cleaning Supplies Required

Ventilation During Cleaning

Cleanup - Remote/Backpack Kits

Supplies for Remote Cleaning

Solvent Cleaning Ventilation

Reassembly and Maintenance

Post-Cleaning Reassembly

Troubleshooting Common Issues

Motor and Spraying Problems

Advanced Troubleshooting

Spray Pattern and Leak Issues

Motor Overheating Solutions

Replacement Parts Information

Atomizer Valve Replacement

Piston and Spring Replacement

Parts Identification List

Component Identification

Repacking Sprayer Components

Fitting Sprayer into Case

Wagner Limited Warranty

Spray Tip Lifetime Warranty

Related product manuals