WALKER FILTRATION PD006 - Maintenance; Servicing and Service Intervals

23
Pro Dry Instruction Manual | Walker Filtration | www.walkerltration.com
Servicing
Section 6: Maintenance
1ST ANGLE
GENERAL TOLERANCE SYSTEM - UNLESS OTHERWISE STATED
G
H
± 0.25 mm = 0.0
0.00 = ± 0.10 mm 0 NOM
0
=
=
± 0.50 mm
± 1.00 mm
F
E
± 0.50 ° 0.0° =
ANGULAR :-
REVISED BY
CREATED BY
DESIGN REF.
PROJECT REFERENCE
REMOVE ALL SHARP EDGES
ASK! ALL DIMENSIONS IN mm.
DO NOT SCALE DRG. IF IN DOUBT
B
D
C
A4-
DRG. NUMBER
A
REV
$format
DRG SIZE SHEET
1 2 3
TEL: (+44191) 0191 4177816
FAX: (+44191) 0191 4153748
NE37 3ES, ENGLAND
WASHINGTON,TYNE & WEAR
Web: www.walkerfiltration.co.uk
MATERIAL DRG. NUMBER
A4-
DATE
DRG. TITLE DATE
DRG SIZE
SCALE
CHECK
$scale1
REV
$format
TOLERANCE TO BE 50% OF LINEAR
UNLESS STATED GEOMETRICAL
4
TOLERANCE. REFER TO B.S. 8888:2000
5 6
REV CHANGE ORDER DATE
BY
$aei1
$aet1
$aed1
$aeu1
$version
$norm_by
$mat
$ident
$ben1
$changed_at
$created_at
$created_by
$changed_by
$field2
$field3
$sheet
$version
$ident
THIS DRAWING& ANY INFO OR DESCRIPTIVE MATTER SET OUT HERON ARE THE CONFIDENTIAL & COPYRIGHT PROPERTY OF WALKER FILTRATION, & MUST NOT BE DISCLOSED, LOANED, COPIED OR USED FOR MANUFACTURING, TENDERING OR FOR ANY OTHER PURPOSE WITHOUT THEIR WRITTEN PERMISSION. C 2000.
$aei2
$aei3
$aei4
$aei5
$aet2
$aet3
$aet4
$aet5
$aed3
$aed4
$aed5
$aed2
$aeu4
$aeu2
$aeu3
$aeu5
Figure 6.1: Models PD004 – PD035
Maintenance
Front Panel Removal
Models PD004 – PD035 only
• Seegure6.1.
• Using a hex key remove screw from the front panel.
• Open from bottom, allowing top to drop out releasing the
panel entirely.
Tools required
• 4mm hex key
Important information.
Ensure shutdown and start-up procedures are followed prior
to carrying out any maintenance work on the dryer.
Walker Filtration will not accept responsibility for physical
injury, damage or delays caused by failure to observe the
instructions in this manual and manuals provided with your
equipment.
Please refer to Section 11-Spares Information.
Figure 6.2: Models PD004 – PD035 with front panel removed
23
1ST ANGLE
GENERAL TOLERANCE SYSTEM - UNLESS OTHERWISE STATED
G
H
± 0.25 mm = 0.0
0.00 = ± 0.10 mm 0 NOM
0
=
=
± 0.50 mm
± 1.00 mm
F
E
± 0.50 ° 0.0° =
ANGULAR :-
REVISED BY
CREATED BY
DESIGN REF.
PROJECT REFERENCE
REMOVE ALL SHARP EDGES
ASK! ALL DIMENSIONS IN mm.
DO NOT SCALE DRG. IF IN DOUBT
B
D
C
A4-
DRG. NUMBER
A
REV
$format
DRG SIZE SHEET
1 2 3
TEL: (+44191) 0191 4177816
FAX: (+44191) 0191 4153748
NE37 3ES, ENGLAND
WASHINGTON,TYNE & WEAR
Web: www.walkerltration.co.uk
MATERIAL DRG. NUMBER
A4-
DATE
DRG. TITLE DATE
DRG SIZE
SCALE
CHECK
$scale1
REV
$format
TOLERANCE TO BE 50% OF LINEAR
UNLESS STATED GEOMETRICAL
4
TOLERANCE. REFER TO B.S. 8888:2000
5 6
REV CHANGE ORDER DATE
BY
$aei1
$aet1
$aed1
$aeu1
$version
$norm_by
$mat
$ident
$ben1
$changed_at
$created_at
$created_by
$changed_by
$field2
$field3
$sheet
$version
$ident
THIS DRAWING& ANY INFO OR DESCRIPTIVE MATTER SET OUT HERON ARE THE CONFIDENTIAL & COPYRIGHT PROPERTY OF WALKER FILTRATION, & MUST NOT BE DISCLOSED, LOANED, COPIED OR USED FOR MANUFACTURING, TENDERING OR FOR ANY OTHER PURPOSE WITHOUT THEIR WRITTEN PERMISSION. C 2000.
$aei2
$aei3
$aei4
$aei5
$aet2
$aet3
$aet4
$aet5
$aed3
$aed4
$aed5
$aed2
$aeu4
$aeu2
$aeu3
$aeu5
Service Intervals
Pre Filter Element Annually (6000 hrs)
Cartridges Every Two Years (12000 Hrs)
Valves Every Four Years (24000 Hrs)