Why does my W&H Laboratory Equipment sterilizer enter standby mode immediately after opening the chamber door?
If your W&H Laboratory Equipment sterilizer enters standby mode immediately after opening the chamber door, it is likely because the chamber door was not opened after the previous cycle finished and the standby mode delay has expired. Press the standby button to exit.
Why was the sterilization process phase longer than expected on my W&H Lyla?
If the sterilization process phase of a sterilization cycle was longer than expected on your W&H Laboratory Equipment, it means that the chamber temperature dropped below the minimum threshold and the software performed a successful recovery. Wait for cycle completion. If the problem occurs frequently, call technical service.
What does the warning about USB saving mean on my W&H Lyla Laboratory Equipment?
If you are getting a warning about USB saving (HTML and SCL files) on your W&H Laboratory Equipment, check the presence and connection of the USB pen drive. If the problem persists, call service.
General| Model | Lyla |
|---|---|
| Manufacturer | W&H |
| Interface | Touch screen |
| Sterilization Temperature | 134°C |
| Power Supply | 220-240V, 50/60Hz |
| Application | Dental and medical sterilization |
Lists regulations, standards, and directives the sterilizer complies with.
Explains warning and caution symbols used in the manual for hazard identification.
Details symbols found on the sterilizer for user guidance and safety.
Provides context about the manual's content and purpose.
Outlines the manual's purpose for safe and reliable operation.
Specifies the sterilizer's intended applications for medical devices.
Defines the required qualifications for operating the sterilizer.
Details thermal hazards associated with the sterilizer's operation.
Outlines potential electrical hazards and precautions.
Lists unsafe practices and restrictions for sterilizer operation.
Defines user obligations for proper installation, use, and maintenance.
States manufacturer's liability regarding safety, reliability, and performance.
Provides instructions and warnings for unpacking the sterilizer.
Advises checking for damage during transport and handling packaging.
Lists the items included in the sterilizer packaging.
Lists accessories and items not supplied with the sterilizer.
Provides steps for safely relocating the sterilizer before transport.
Details the components of the sterilizer's front and upper internal structure.
Identifies components located behind the service door.
Identifies components on the rear view of the sterilizer.
Describes chamber racks and their capacity for trays and cassettes.
Specifies environmental and placement requirements for the sterilizer.
Details requirements for connecting the sterilizer to the power supply.
Explains requirements for clean water supply and warranty implications.
Provides steps for establishing a Wi-Fi connection for the sterilizer.
Step-by-step guide for the physical installation of the sterilizer.
Instructions for turning the sterilizer on and off.
Explains the elements and layout of the sterilizer's homepage.
Lists and describes the primary functions accessible from the main menu.
Details functions available within the sterilizer's settings menu.
Guides the user through initial setup of language, network, date/time, and name.
Instructions for changing the sterilizer's display language.
Steps to adjust the date, time, and time zone settings.
Guide to setting or changing the sterilizer's name.
Instructions for adjusting the brightness of the sterilizer's display.
Steps for connecting the sterilizer to a network via Ethernet or Wi-Fi.
Explains the requirement for an activation code for user management.
Details how to manage PINs, including changing and resetting them.
Explains the purpose and use of the USB pen drive for cycle reports.
Provides instructions for formatting the USB pen drive.
Explains the sterilizer's standby mode and its energy-saving function.
Steps to manually activate the sterilizer's standby mode.
How to exit the sterilizer's standby mode.
Instructions for adjusting the delay time before entering standby mode.
Details features and procedures for managing user accounts.
Guides on setting traceability options and requested user information.
Guide to selecting and configuring available printers for the sterilizer.
Instructions for selecting and setting up a label printer.
Details how to use the label printing functionality, including automatic and manual options.
Explains the structure and content of printed labels.
Overview of tests to validate sterilizer performance.
Details the Bowie and Dick test for textile load sterilization.
Explains the Helix test for validating performance on hollow items.
Explains how to interpret the results of the Helix test.
Guides on documenting the Helix test results.
Details the Vacuum test for pneumatic circuit tightness.
Provides troubleshooting steps if the Vacuum test fails.
Covers cleaning, lubrication, and packaging of instruments for sterilization.
Steps to prepare the sterilizer before starting a cycle, including water filling.
Instructions for attaching and detaching the steam diffuser plate.
Steps for filling the sterilizer's clean water tank.
Guide on how to insert the chamber rack into the sterilizer.
Tips for optimizing drying and cycle times.
Lists available sterilization cycles and their purposes.
Details the ECO-B mode for reduced cycle duration and energy consumption.
Procedures for activating B-type cycles using an activation code.
Step-by-step guide to start a sterilization cycle immediately.
How to schedule the start date and time for sterilization cycles.
Instructions for setting the drying time for sterilization programs.
How to check real-time and end-of-cycle parameters.
Explains the information displayed during a running sterilization cycle.
Procedures for completing a cycle and unloading the sterilizer.
Instructions on how to safely stop a running sterilization cycle.
Specifies where summarized and analytical cycle reports are stored.
Details the format (HTML, SCL) of stored sterilization reports.
Explains behavior when cycles cannot be saved to USB.
How to access and view the history of sterilization cycles.
Steps to print or save cycle reports to a USB drive.
Instructions for printing traceability labels for specific cycles.
Procedure to save all cycle reports to the USB pen drive.
Guides on setting remote storage for saving sterilization cycle reports.
How to test the functionality of remote data storage.
Instructions for saving all cycle reports to a remote folder.
Details the structure and data fields found in a cycle report.
Safety warnings and precautions before performing maintenance.
Outlines routine maintenance tasks to be performed by the user.
Explains how the sterilizer monitors and alerts for expired consumables.
Procedure for manually resetting counters after replacing consumables.
Step-by-step guide for cleaning the door gasket and chamber face.
Instructions for cleaning the sterilizer chamber and its accessories.
Step-by-step guide for cleaning the chamber filter.
Instructions for cleaning the external covers of the sterilizer.
Guide for replacing the bacteriological filter.
Guide for replacing the dust filter.
Overview of steps for cleaning the water tanks.
Initial steps to prepare the sterilizer for water tank cleaning.
Instructions on how to access the sterilizer's water tanks.
Detailed steps for cleaning the internal surfaces of the water tanks.
Guide for replacing the door gasket.
Outlines the general check and service required for 4000 cycles or five years.
Specifies actions (Replace, Clean, Check) for various sterilizer elements.
Instructions for draining the water tanks when the sterilizer is not in use.
Outlines responsibilities and regulations for sterilizer disposal.
Lists error codes and corresponding actions for troubleshooting.
Explains system messages and alerts, and the required actions.
Steps to manage errors that occur during sterilization cycles.
How to view and save the list of past errors.
Describes the information displayed on the error page after a reset phase.
Lists warning messages and their implications.
Procedure to reset the safety thermostat after it has operated.
A table listing common problems, their causes, and solutions.
Critical warnings regarding high pressure and temperature during emergency opening.
Explains the need for 9V batteries for the auxiliary unlocking procedure.
Step-by-step guide for opening the door in an emergency.
Information on available sterilization cycles and their specifications.
Lists and categorizes the standard S-type and B-type sterilization cycles.
Presents technical data for S-type sterilization cycles.
Presents technical data for B-type sterilization cycles.
Table showing total cycle times for different loads and versions.
Table showing total cycle times for different loads and versions.
Specifies the maximum load weights for various instruments and cycles.
Defines codes and descriptions for various sterilization cycle phases.
Illustrates the pressure profile for S-type sterilization cycles.
Illustrates the pressure profile for B-type sterilization cycles.
Details specifications for the water supply system.
Details specifications for the power supply system.
Specifies environmental and spatial requirements for installation.
Provides technical specifications for the sterilizer chamber.
Details water quality requirements and consumption.
Identifies validation points (hottest/coldest) for sterilizer performance.
Illustrates data communication and water system connection diagrams.
Lists maximum content of minerals and water specifications according to EN13060.
Lists various chamber racks and trays with their specifications.
Lists consumables, their part numbers, and replacement frequency.
Lists activation codes, their descriptions, and part numbers.
Information on finding authorized service partners.
A checklist for verifying proper installation and user training.
Fields for recording serial number, purchase, and installation details.
Provides fax and mail addresses for submitting the installation checklist.
A form for logging Helix test results and effectiveness over time.
To Next Page
