What to do if my Warmhaus Enerwa Plus 2530 Boiler shows error E 13?
If your Warmhaus Boiler displays error E 13, it indicates an over temperature flue gas outlet value exceeding 105 C°. Call for authorised service.
What to do if my Warmhaus Enerwa Plus 2530 shows error E 06?
If your Warmhaus Boiler shows error E 06, this indicates a gas supply failure. To resolve this: first, reset and restart the boiler. Check if the boiler's central heating valves are open; if closed, open them. Also, ensure that all radiator valves are open, with a minimum of 3 meters of radiator open. Reset the boiler again to see if the problem is resolved. If it continues, call an authorized service.
What to do if my Warmhaus Enerwa Plus 2530 shows error E 07?
If your Warmhaus Boiler displays error E 07, it indicates a lack of water in the system, pump blockage, pump failure, pump harness issue, or installation blockage. First, reset the boiler to see if the problem resolves. Check that the boiler's central heating valves are open; if they are closed, open them. Also, ensure all radiator valves are open, with a minimum of 3 meters of radiator open. Reset the boiler again and check. If the issue persists, call an authorized service.
What to do if my Warmhaus Enerwa Plus 2530 shows error E 03?
If your Warmhaus Boiler is showing error E 03, this indicates high water pressure in the boiler (greater than 2.8 bar). Initially, check the filling tap of the boiler and ensure it is closed. During boiler operation, the safety valve may continue to drain water, so ensure it's connected to a drain line. If your plumbing line has a drain cock, turn the boiler off and let the pressure drop to 1-1.5 bar, then switch it on again. If the pressure increase reoccurs, call an authorized service.
What to do if my Warmhaus Boiler shows error E 20?
If your Warmhaus Boiler displays error E 20, this indicates a lack of water in the system, pump blockage, pump failure, pump harness issue or installation blockage. Begin by resetting the boiler to check if the problem is resolved. Ensure the boiler's central heating valves are open; if closed, open them. Check that all radiator valves are open, with a minimum of 3 meters of radiator open. Reset the boiler again and check. If the issue persists, call an authorized service.
What to do if my Warmhaus Enerwa Plus 2530 Boiler shows error E 09?
If your Warmhaus Boiler displays error E 09, it indicates a lack of water in the system, pump blockage, pump failure, pump harness issue, or installation blockage. Start by resetting the boiler to see if the problem is resolved. Ensure the boiler's central heating valves are open; if they are closed, open them all. Check that all radiator valves are open, with a minimum of 3 meters of radiator open. Reset the boiler again and check if the problem is resolved. If the issue persists, call an authorized service.
What to do if my Warmhaus Boiler shows error E 04?
If your Warmhaus Boiler shows error E 04, it indicates that the domestic heating water temperature sensor is faulty. Call for authorised service.
What to do if my Warmhaus Boiler shows error E 08?
If your Warmhaus Boiler displays error E 08, it means that either the Condensate Syphon is blocked or there is an issue with the electronic board. Call for authorised service.
What to do if my Warmhaus Boiler shows error E 17?
If your Warmhaus Boiler displays error E 17, it indicates that the FLOW and LIMIT Sensor (double NTC) is faulty. To resolve this, reset and restart the boiler. If the problem persists, call an authorized service.
What to do if my Warmhaus Enerwa Plus 2530 shows error E 05?
If your Warmhaus Boiler is showing error E 05, it means the central heating FLOW temperature sensor is faulty. Try resetting and restarting the boiler. If the problem continues, call an authorized service.
General| Type | Combi Boiler |
|---|---|
| Fuel Type | Natural Gas / LPG |
| Ignition Type | Electronic |
| Flue Diameter | 60/100 mm |
| Operating Pressure | 3 bar |
| Efficiency | 93% (at 30% power) |
To Next Page