Warmup WA-TSTAT-V User Manual

Warmup Thermostat type WA-TSTAT-V
USER MANUAL
Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . 1
2. Getting started . . . . . . . . . . . . . . . . . . . . . . . 1
3. General Display . . . . . . . . . . . . . . . . . . . . . . . 1
4. LED . . . . . . . . . . . . . . . . . . . . . . . 2
5. Buttons . . . . . . . . . . . . . . . . . . . . . . . 2
6. Menus for Setting Up the Thermostat . . . . . . . . . . . . . . . . . 2
6.1. Operation . . . . . . . . . . . . . . . . . . . . . . . 2
6.1.1. Auto . . . . . . . . . . . . . . . . . . . . . . 2
6.1.2. Manual . . . . . . . . . . . . . . . . . . . . . 2
6.1.3. Comfort . . . . . . . . . . . . . . . . . . . . . 2
6.2. Setting 4-event . . . . . . . . . . . . . . . . . . . . . 2
6.2.1. Example of Scheduling 4-event Set-up . . . . . . . . . . . . . 2
6.3. Programming . . . . . . . . . . . . . . . . . . . . . . 2
6.4. General Settings . . . . . . . . . . . . . . . . . . . . . 2
6.4.1. Language . . . . . . . . . . . . . . . . . . . . . 2
6.4.2. Time . . . . . . . . . . . . . . . . . . . . . . 2
6.4.3. Day . . . . . . . . . . . . . . . . . . . . . . 3
6.4.4. Temperature . . . . . . . . . . . . . . . . . . . . 3
6.4.5. Child lock . . . . . . . . . . . . . . . . . . . . . 3
6.4.6. Heater . . . . . . . . . . . . . . . . . . . . . . 3
6.4.7. Covering . . . . . . . . . . . . . . . . . . . . . 3
6.4.8. Sub Floor . . . . . . . . . . . . . . . . . . . . . 3
6.4.9. Application . . . . . . . . . . . . . . . . . . . . 3
6.5. Service . . . . . . . . . . . . . . . . . . . . . . . 3
6.6. Contact Details . . . . . . . . . . . . . . . . . . . . . 3
6.7. Engineer Settings . . . . . . . . . . . . . . . . . . . . . 3
6.7.1. Readout . . . . . . . . . . . . . . . . . . . . . 3
6.7.2. Temp. Settings . . . . . . . . . . . . . . . . . . . 3
6.7.3. Adaptive function . . . . . . . . . . . . . . . . . . . 3
6.7.4. Offset . . . . . . . . . . . . . . . . . . . . . . 4
6.7.5. Fil Pilote* . . . . . . . . . . . . . . . . . . . . . 4
6.7.6. Reset . . . . . . . . . . . . . . . . . . . . . . 4
7. Error Messages . . . . . . . . . . . . . . . . . . . . . . . 4
8. F actory settings . . . . . . . . . . . . . . . . . . . . . . . 4
9. Appendix . . . . . . . . . . . . . . . . . . . . . . . 4
9.1. Table of Compatibility . . . . . . . . . . . . . . . . . . . . 4
9.2. Heat Definitions . . . . . . . . . . . . . . . . . . . . . 4
Type: WA-TSTAT-V
57628 09/06 (BJ)
1. Introduction
The NewStar thermostat can switch on your
heating system at pre-determined times on
different days of the week. It is possible to set 4
periods called events each day with different
temperatures. The thermostat comes with a
default schedule that is suitable for most
installations. Unless you change these settings,
the thermostat will operate to this default
program.
Working with lower temperatures during times
that the room is unoccupied will lower your
energy costs without reducing the comfort. The
thermostat has an adaptive function that
automatically changes the start time of a
heating period so that the desired temperature
is reached at the time that you set. After 3 days
the adaptive function has learned when the
heating must be switched on.
2. Getting started
Quick set-up:
The first time you connect the power or after a
reset, the display will show you “Welcome to
Warmup”.
Push accept button. Then you can select:
• Language
• Time
• Day
• Temperature
• Child lock
• Heater?
• C overing?
• Sub floor
• Application
Use the navigation buttons for selecting /
changing in the menus.
Important:
You have, as minimum, to select “Heater” and
“covering” to define the type of heater and
covering, before you can start up the
thermostat.
For further information, see point:
5. Buttons.
6.4. General settings.
3. General Display
The display will normally
show the period ( day, night,
home, out ) , the current
temperature, and the time.
The period is indicated by a symbol. Below you
can see a list of some of the symbols:
At work
At home
Day
Night
Language
English . . . . . . page 1 - 4
German . . . . . . page 5 - 8
French . . . . . . page 9 - 12
Portuguese . . . . . page 13 - 16

Warmup WA-TSTAT-V Specifications

General

Model Number	WA-TSTAT-V
Maximum Load	16A
Control	Touchscreen
Wi-Fi Connectivity	Yes
Temperature Range	41°F to 104°F (5°C to 40°C)
Compatibility	Electric Underfloor Heating Systems
Display	LCD
Floor Sensor	Yes
Air Sensor	Yes
Programming Modes	7-day programmable
Dimensions	120mm x 70mm x 25mm

Summary

Introduction

Getting Started

Quick Set-up

Describes the initial steps after connecting power or reset, guiding through basic settings.

General Display

LED Status Indicators

LED Signal

Details the meaning of different LED signals like constant red, blinks, and no light.

User Buttons and Reset

Navigation Buttons

Explains the function of navigation buttons like Up, Down, Accept/Change, Back/Cancel.

Reset Function

Describes how to perform a factory reset using the reset button and its consequences.

Thermostat Setup Menus

6.1. Operation Modes

Allows choosing between Auto, Manual, or temporary Comfort temperature modes.

6.2. Setting 4-Event Schedule

Enables programming of 4 temperature events per day for a 7-day week.

6.3. Programming Options

Offers options for scheduling the 4-event system (e.g., Mon-Fri, Sat-Sun).

6.4. General Settings

Contains various system-wide configurations like language, time, and day.

Day Setting

Temperature Settings

Temperature Scale

Allows selection of temperature units (°C, °F, or 1-10 scale).

Display Information

Controls which information (time, set point, air temp.) is displayed.

Child Lock Feature

Heater Type Configuration

Floor Covering Configuration

Sub Floor Type Configuration

Regulator Application Settings

Floor Temperature Control

Configures the thermostat for floor temperature control using one or two sensors.

Air Control with Floor Limit

Sets up air temperature control with an additional floor limit sensor for protection.

Regulator Control Mode

Allows timed on/off sequences for heating, adjustable by percentage.

External Control Mode

Defines the thermostat as a slave unit controlled by a master thermostat.

Service Information

Contact Details

Engineer Settings

6.7.1. Readout Data

Displays current temperatures and various operational statistics.

6.7.2. Temperature Limits

Allows setting minimum and maximum temperature limits for sensors.

6.7.3. Adaptive Function

Enables or disables the adaptive function for optimized heating start times.

Offset Calibration

Fil Pilote Function

Reset Options

Reset 2: Engineer Settings

Resets Engineer settings to factory defaults.

Reset 3: Settings and History

Resets Engineer settings and deletes history data.

Error Message Handling

Internal Failure

Indicates the cause and action for internal system failures.

External Failure

Indicates the cause and action for external system failures.

Factory Default Settings

Appendix Information

9.1. Compatibility Table

Lists compatibility between heater types and floor coverings.

9.2. Heat Definitions

Provides definitions and compatibility codes for various heating configurations.

Controller Setting WA-XSTAT

Program Choice Options

Lists available program choices for the thermostat.

Floor Temperature Control Setup

Details how to set up floor temperature control.

Floor Control with 2 Sensors

Explains setting up floor control using dual sensors.

Air Temperature Control Setup

Describes the configuration for air temperature control.

Air Control with Floor Limit

Covers air control with an added floor limit.

Regulator Control Mode

Explains the regulator control mode.

External Control Mode

Outlines settings for external control mode.

Technical Data

Important Safety Instructions

Fault Location and Troubleshooting

Environment and Recycling Guidelines

Recycling Obsolete Appliances