Watlow 988 series - Page 76

A.6
Data Communications with the Watlow Series 988 Family Appendix
Hysteresis [HYS3]
981-984 5.6
986-989 6.11
996-999 7.5
Process Range [PRC3]
981-984 5.9
986-989 6.15
996-999 7.9
Status [OT3S]
996-999 7.8
Output 4
Hardware Type [OTY4]
981-984 5.9
986-989 6.14
996-999 7.8
Output Menu Lockout [OTPT]
986-989 6.14
996-999 7.8
Output Process Range
Channel A [PRCA]
996-999 7.9
Channel B [PRCB]
996-999 7.9
Output State
Event 3 981-984 [ENT3] 5.5
Event 4 981-984 [ENT4] 5.5
Outputs, Test [TOUT]
981-984 5.11
986-989 6.17
996-999 7.11
P
parity 3.2
parity bit 1.4
Percent Power Output [PWR]
981-984 5.10
986-989 6.15
PID Set A Menu Lockout [PIDA]
986-989 6.14
PID Set B Menu Lockout [PIDB]
986-989 6.14
PID Set Crossover [PID2]
986-989 6.15
Power Outage Response [POUT]
981-984 5.9
Process Deviation Display [DEV]
981-984 5.5
986-989 6.9
Process Range
Output [PRCA], [PRCB]
996-999 7.9
Output 1 [PRC1]
981-984 5.9
986-989 6.15
Output 2 [PRC2]
981-984 5.9
986-989 6.15
Output 3 [PRC3]
981-984 5.9
986-989 6.15
996-999 7.9
Process Value for PID Switch [PROC]
986-989 6.15
Program a File Step [STP]
981-984 5.11
Program Start Point [PSTR]
981-984 5.9
Program Type [PTYP]
981-984 5.9
Prompts, COM Menu 3.2
Proportional Band
Output 1
981-984 [PB1] 5.9
986-989 [PB1A], [PB1B] 6.14
996-999 [PB1A], [PB1B] 7.8
Output 2
981-984 [PB2] 5.9
986-989 [PB2A], [PB2B] 6.14
996-999 [PB2A], [PB2B] 7.8
Protocol 1.1
prompt [Prot] 3.1-3.2
XON/XOFF RS-232 4.2
pull-down resistors 2.3
Q
Query Any Step
Program [STP] 5.13
Quick BASIC 1.5
R
Ramp Rate
986-989 [RATE] 6.16
996-999 [RTA], [RTB] 7.10
Ramping Initiation
986-989 [RP] 6.16
996-999 [RPA], [RPB] 7.10
Range High
Input 1 [RH1]
981-984 5.10
986-989 6.15
996-999 7.9
Input 2 [RH2]
981-984 5.10
986-989 6.15
996-999 7.9
Retransmit [ARH]
981-984 5.4
986-989 6.8
996-999 7.2
Range Low
Input 1 [RL1]
981-984 5.10
986-989 6.16
996-999 7.9
Input 2 [RL2]
981-984 5.10
986-989 6.16
996-999 7.9
Retransmit [ARL]
981-984 5.4
986-989 6.8
996-999 7.2
Rate
Output 1
981-984 [RA1] 5.10
986-989 [RA1A], [RA1B] 6.15
996-999 [RA1A], [RA1B] 7.9
Output 2
981-984 [RA2] 5.10
986-989 [RA2A], [RA2B] 6.15
996-999 [RA2A], [RA2B] 7.9
remote device 1.1
Remote Set Point [RSP]
986-989 6.16
Index
Reset
Output 1 [RE1]
981-984 5.10
Output 1 PID [RE1A], [RE1B]
986-989 6.15
996-999 7.9
Output 2 [RE2]
981-984 5.10
Output 2 PID {RE2A], RE2B]
986-989 6.15
996-999 7.9
Resume a Program [RESU]
981-984 5.10
Retransmit
Range High [ARH]
981-984 5.4
986-989 6.8
996-999 7.2
Range Low [ARL]
981-984 5.4
986-989 6.8
996-999 7.2
RS-232 1.3, 2.1, 4.2
RS-422 1.3, 2.1, A.1
RS-422 wiring 2.4
RTD Calibration
Input 1 [RTD1]
981-984 5.10
986-989 6.16
996-999 7.10
Input 2 [RTD2]
986-989 6.16
996-999 7.10
rules, data 4.1
run/hold mode
981-984 5.2
Run/Hold Status [RHS]
981-984 5.10
S
Sensor Failure Output [FAIL]
986-989 6.10
996-999 7.5
serial interface 2.1
Serial Number [SRNB], [SRNT]
981-984 5.10
986-989 6.16
996-999 7.10
Set Point 1 [SP1]
986-989 6.16
Set Point 2
986-989 [SP2] 6.16
996-999 [SP2A], [SP2B] 7.10
Set Point 2 Type [SP2C]
986-989 6.17
Set Point Channel A [SPA]
996-999 7.10
Set Point Channel B [SPB]
996-999 7.10
Set Point Value PID Switch [STPT]
986-989 6.17
Setup Menu [`SEt] 2.1, 3.2, 4.4
Simulate HOLD Key [HOLD]
981-984 5.6
Slidewire Dead Band % [HUNT]
981-984 5.6
986-989 6.11
Slidewire Hysteresis [SHYS] 6.16