EasyManua.ls Logo

Wayne-Dalton classicdrive 3018 - User Manual

Wayne-Dalton classicdrive 3018
46 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
INSTALLATION INSTRUCTIONS AND OWNER’S MANUAL
Chain/ Belt Drive
Models: 3018, 3018DLX, 3522, 3522DLX
IMPORTANT NOTICE!
Read the enclosed instructions carefully before installing/operating
this garage door opener. Pay close attention to all warnings and
notes. This manual MUST be attached to the wall in close proximity
to the garage door.
© Copyright 2006 Wayne-Dalton Corp. Part No. 326568 NEW 6/6/2006
FOR RESIDENTIAL SECTIONAL OVERHEAD GARAGE DOORS ONLY!
DO NOT USE ON ONE PIECE DOORS!
IMPORTANT! THE DOOR AND OPENER WILL NOT FUNCTION PROPERLY UNTIL
INFRARED SAFETY SENSORS ARE INSTALLED AND PROPERLY ADJUSTED!
GARAGE DOORS & OPENERS

Table of Contents

Questions and Answers

  • D
    Daniel MurphyAug 15, 2025
    What to do if my Wayne-Dalton classicdrive 3018 reverses before closing?
    • S
      Sarah BurnsAug 15, 2025
      If your Wayne-Dalton Garage Door Opener reverses before fully closing and the light flashes, it indicates that the obstruction sensing system has been activated. This could be due to binding in the door's travel, loose or hanging objects activating the infrared safety sensor, or insufficient closing force. Check for any obstructions in the door's path, remove any hanging objects, and adjust the closing force.
  • B
    Brandon RobertsAug 18, 2025
    Why won't my Wayne-Dalton classicdrive 3018 Garage Door Opener work with the wall button or remote?
    • A
      acostajosephAug 18, 2025
      If your Wayne-Dalton Garage Door Opener isn't working from either the wall button or the remote, the possible causes are: no power to the opener, a short circuit in the wiring to the opener or wall button, or the motor protector has tripped due to excessive use. To troubleshoot, check the cord to the outlet, wall switch, and circuit breaker. Isolate the issue by disconnecting the wires at the opener from the wall station. If the motor protector tripped, allow the motor to cool for 20 minutes and try again.
  • W
    Whitney BellAug 21, 2025
    What to do if my Wayne-Dalton classicdrive 3018 closes and then reopens?
    • W
      Wayne HendrixAug 22, 2025
      If your Wayne-Dalton Garage Door Opener closes and then returns to the fully open position, and the opener light flashes, the issue might be due to the door arm adjustment, the close travel adjustment being set beyond the normal door position, obstructions on the floor, or insufficient down force. Adjust the door arm and close travel. Check for stones or ice under the door and remove them. Also, adjust the downforce, ensuring obstruction testing is performed whenever the downforce is changed.
  • C
    Crystal WilliamsAug 25, 2025
    Why does my Wayne-Dalton classicdrive 3018 Garage Door Opener light flash and the door doesn't open?
    • E
      Erin JohnsonAug 26, 2025
      If your Wayne-Dalton Garage Door Opener light flashes and the door doesn't open, it usually means something is obstructing the door's travel, the opening force is insufficient, or there's a buildup of ice and snow around the door. Disconnect the door from the operator and operate it by hand to find any obstructions, or call a service person. Adjust the opening force and clear any ice or snow from around the door area.
  • M
    Matthew MoralesAug 28, 2025
    How to fix a Wayne-Dalton classicdrive 3018 Garage Door Opener that works from the wall button but not the remote?
    • H
      Howard HernandezAug 28, 2025
      If your Wayne-Dalton Garage Door Opener works from the wall button but not the remote, the radio control system may be non-operational. Try replacing the battery in the transmitter. If that doesn't work, the transmitter may not be programmed to the opener. If two or more transmitters don’t work, have the motor control board tested.
  • T
    Thomas MccoyAug 31, 2025
    What should I do if my Wayne-Dalton Garage Door Opener stops before fully closing?
    • J
      joshuamorganAug 31, 2025
      If your Wayne-Dalton Garage Door stops and does not close fully, the close limit might not be set properly. To fix this, adjust the close travel with a screwdriver, turning it clockwise to the desired setting. A 1/4 turn equals 1” of travel.
  • R
    Ryan BarnettSep 3, 2025
    How to adjust a Wayne-Dalton Garage Door Opener that doesn't open fully?
    • A
      Adrian FrostSep 4, 2025
      If your Wayne-Dalton Garage Door does not open fully and the light does not flash, the open limit is likely not set properly. Adjust the open travel with a screwdriver, turning it counter-clockwise to the desired setting. A 1/4 turn equals 1” of travel.
  • A
    Andrew WestSep 7, 2025
    Why does my Wayne-Dalton classicdrive 3018 Garage Door Opener move briefly and then reopen?
    • J
      John MccormickSep 7, 2025
      If, when activated with the door in the fully open position, your Wayne-Dalton Garage Door Opener travels for a second or less, stops, returns to the fully open position, and the light flashes, the infrared safety sensors may be out of adjustment or defective, or there may be obstructions in the door opening. Check the alignment of the infrared safety sensors according to the instructions and look for any objects blocking the infrared safety sensors.
  • H
    Howard LopezSep 10, 2025
    Why does my Wayne-Dalton Garage Door Opener light flash after the door fully opens?
    • T
      Theresa TranSep 12, 2025
      If your Wayne-Dalton Garage Door fully opens and then the light flashes, the open limit is set too high, and the trolley is hitting the stop bolt. To resolve this, adjust the open travel with a screwdriver, turning it clockwise to the desired setting. A 1/4 turn equals 1” of travel.

Summary

Package Contents

Pre-Installation Inspection

Pre-Installation Steps

Identify Your Door

Verify door type is sectional and not one-piece.

Test Your Door

Check door balance and smooth operation for safety.

Pre-Assembly Check

Ensure limit switch is set to the door closed position.

Important Installation Instructions

Rail Assembly

Removing Tie Wrap

Remove tie wrap securing the upper door arm.

Mounting Front Rail Assembly

Attach the front rail assembly to the intermediate rails.

Setting Idler

Install the idler assembly and secure with U-bolt.

Rail Assembly Alignment And Chain Or Belt Setting

Align rails using a tool and set chain/belt tension.

Attaching Rail to Opener

Align and attach the rail to the opener's driver gear.

Positioning and Installing Front Wall Bracket

Attach Unit to Front Wall Bracket

Connect the rail assembly to the front wall bracket.

Positioning Motor End of Opener

Support the opener's motor end for installation.

Mounting Opener End

Mounting and Lighting Components

Mounting Door Bracket

Secure the door bracket to the top section of the door.

Installing Light

Install the light bulb and lens into the opener housing.

Wired Wall Station and Entrapment Label Installation

Safety Sensor Installation and Wiring

Install Sensor Wiring

Route and secure sensor wires to the opener.

Connect Safety Sensors to Opener

Connect sensor wires to the opener terminals, observing polarity.

Connecting Opener to Power

Connect Opener to Outlet

Plug the opener into a properly grounded outlet.

Connecting Trolley to Latch Assembly

Alignment of Wired Infrared Safety Sensors

Setting Trolley Close Position

Connecting Door Arm to Door

Door Travel Adjustments

Setting Door Close Travel

Adjust the close travel limit for proper door stopping.

Setting Door Opening Travel

Adjust the open travel limit for proper door stopping.

Safety and Obstruction Tests

Contact Obstruction Test

Test door reversal upon contacting a 1-1/2" high object.

Safety Sensor Obstruction Test

Test sensor reaction to a 6" high object on the floor.

Programming Wireless Keyless Entry

Installing Wireless Keyless Entry

Power Connection (Permanent Wiring Option)

Adjustable Door Bracket Option

Setting Trolley Position and Connecting Door Arm

Important Safety Instructions and Operation

Door Activation

Describes how the door moves upon activation.

How the Light Works

Explains the function of the opener's indicator light.

Operating Controls and Settings

Operating the Wired Wall Station

Explains the function of the Up/Down and Light buttons.

Customizing Settings

Details multi-door programming for transmitters.

Opener Controls

Describes the program button functions on the opener.

Primary Programming for HomeLink

Alternate Programming for HomeLink

Adjustments

Opening and Closing Force

Adjust force settings for safe door operation.

Contact Obstruction Sensing

Adjust settings for proper obstruction reversal.

Positive Mechanical Door Lock

Adjust the mechanical lock for the closed position.

Programming Transmitters

Maintenance

Monthly Maintenance

Lubricate hinges, inspect fasteners, test emergency disconnect.

Twice a Year Maintenance

Check chain tension and replace batteries.

Troubleshooting

Wayne-Dalton classicdrive 3018 Specifications

General IconGeneral
Horsepower1/2 HP
Drive TypeChain Drive
Voltage120V
Remote Controls Included2
Battery BackupNo
Speed7 inches per second
SecurityRolling Code
Motor TypeAC

Related product manuals