How to adjust close limit on Wayne-Dalton Quantum 3314?
If your Wayne-Dalton Garage Door Opener door stops and does not close fully, the close limit might not be set properly. To fix this, adjust the close travel with a screwdriver, turning it clockwise to the desired setting. A 1/4 turn equals 1” of travel.
Why my Wayne-Dalton Garage Door Opener won’t work from wall button or radio control?
If your Wayne-Dalton Garage Door Opener doesn't work when you use the wall button or the radio control, the issue might stem from a few causes. First, there might be no power reaching the opener, so check the cord, outlet, wall switch, and circuit breaker. Second, a short circuit in the wires connecting to the opener or wall button could be the culprit; you can isolate this by disconnecting the wires at the opener from the wall station. Lastly, the Motor Protector might have tripped due to excessive use; allow the motor to cool down for about 20 minutes before trying again.
Why does my Wayne-Dalton Quantum 3314 Garage Door Opener reverse before closing?
If your Wayne-Dalton Garage Door Opener reverses direction before fully closing and the opener light flashes, it indicates that the obstruction sensing system has been activated. This could be due to a few reasons. First, check for any binding in the door's movement, such as issues with the door stopping or the tracks. Second, remove any loose or hanging objects that might be activating the Infrared Safety Sensor. Lastly, the closing force might be insufficient, so you should adjust it.
What to do if my Wayne-Dalton Quantum 3314 door does not open and opener light flashes?
If your Wayne-Dalton Garage Door Opener door does not open and the opener light flashes, it could be due to a few reasons. First, there might be something obstructing the door's path, so disconnect the door from the operator and manually operate the door to find any obstructions. Alternatively, call a service person. Second, the opening force might be insufficient, so you may need to adjust it. Finally, a build-up of ice and snow around the door could be the problem, so shovel and clear the area.
Why Wayne-Dalton Quantum 3314 works from wall button but not remote?
If your Wayne-Dalton Garage Door Opener works from the wall button but not from the radio control, the radio control system may not be working correctly. You can try the following: * Replace the battery in the transmitter if it's weak or dead. * Ensure the Security Code matches between the receiver and transmitter. * If multiple transmitters aren’t working, have the Motor Control Board tested.
Why does my Wayne-Dalton Garage Door Opener stop mid-close?
If your Wayne-Dalton Garage Door Opener door stops traveling for 1 second at the mid-point during close and then continues to close, it is likely due to a weak battery in the Wireless Infrared Safety Sensors. Replace the batteries in the Wireless Infrared Safety Sensors.
Why does my Wayne-Dalton Garage Door Opener light flash after opening?
If your Wayne-Dalton Garage Door Opener fully opens and then the light flashes, it means the open limit is set too high and the trolley is hitting the stop bolt. Adjust the open travel with a screwdriver, turning it counter-clockwise to the desired setting. A 1/4 turn equals 1” of travel.
What does it mean when my Wayne-Dalton Garage Door Opener light flashes and the door stops after 1 second?
If, when activated with the door in the fully open position, your Wayne-Dalton Garage Door Opener door travels for 1 second, stops, returns to the fully open position, and the light begins to flash, it could be due to several reasons. First, the infrared safety sensors may be out of adjustment or defective, so their alignment should be checked per instructions. Second, check the batteries and contact points in the wireless safety sensors. Finally, there may be obstructions in the door opening blocking the infrared safety sensors.
Wayne-Dalton Quantum 3314 works from wall button but not remote: Why?
If your Wayne-Dalton Garage Door Opener works from the wall button but not from the radio control, the radio control system may be non-operational. Try replacing the battery in the transmitter. If that doesn't work, the security code may not be matched between the receiver and transmitter. If two or more transmitters don’t work, have the Motor Control Board tested.
What to do if Wayne-Dalton Quantum 3314 reverses before closing?
If your Wayne-Dalton Garage Door Opener reverses travel before reaching the fully closed position and the opener light flashes, it indicates the activation of the obstruction sensing system. Check for any binding in the door travel, such as the door 'stopping' or issues with the door tracks. Also, remove any loose or hanging objects on the door that might be activating the Infrared Safety Sensor. Finally, ensure that closing force is properly adjusted.
Controls door movement via button, transmitter, or wall station.
Manual disconnect for power failure with automatic reconnect.
Light turns on automatically with activation, stays on for 4 minutes.
Locks door in closed position when properly adjusted.
Flashes after sensing an obstruction or safety system malfunction.
Features a permanently lubricated, thermally protected motor with auto reset.
Independent force adjustments to reverse door on obstruction.
Wired or wireless sensors detect obstructions and reverse door.
Controls door motion and overhead light, offers advanced features.
Opener can learn and operate with Homelink™ transceivers.
Uses rolling codes to prevent unauthorized access.
Checks door balance by ensuring it stays in position when lifted halfway.
Verifies door remains clear of opening at full open position without drift.
Adjusts the force used by the opener for opening and closing.
Sets how the opener reacts to obstructions during closing.
Adjusts the mechanical lock for securing the door.
Explains how to start the door opener using various devices.
Describes door movement based on opener activation and obstructions.
Explains opener light functions and flashing indicators.
Provides instructions for operating the wireless keyless entry system.
Details the functions and operation of the wireless wall station.
Explains the functions of the PROGRAM SWITCH on the power head unit.
Explains how to manually operate the door during power failure.
Guides on programming HomeLink™ to the power head unit.
Outlines monthly maintenance tasks for the opener system.
Details semi-annual maintenance, including chain tension.
Lists annual maintenance tasks, including lubrication and battery checks.
General| Horsepower | 1/2 HP |
|---|---|
| Drive Type | Chain Drive |
| Voltage | 120V |
| Frequency | 60 Hz |
| Remote Control | Yes |
| Safety Sensors | Yes |
| Speed | 7 inches per second |
| Maximum Door Weight | 500 lbs |
| Remote Controls Included | 2 |
| Battery Backup | No |
| Smartphone Control | No |
| Maximum Door Height | 7 feet |
To Next Page