Weider 21 Dumbell Storage Rack User Manual

1. Press a 50mm Square Outer Cap (8) onto each end of
the two Frames (2).
2. Attach a Vertical Tube (1) onto one of the Frames (2)
with two M8 x 60mm Bolts (7), four M8 Washers (6),
and two M8 Nylon Locknuts (5). Repeat this step with
the other Vertical Tube and Frame.
3. Attach a Rack (3) to the lower holes in a Vertical Tube
(1) with two M8 x 65mm Bolts (4), two M8 Washers (6),
and two M8 Nylon Locknuts (5). Attach the Rack to the
other Vertical Tube in the same manner.
4. Attach the other Rack (3) to the upper holes in a
Vertical Tube (1) with two M8 x 65mm Bolts (4), two M8
Washers (6), and two M8 Nylon Locknuts (5). Repeat
this step to attach the Rack to the other Vertical Tube.
5. Insert a 50mm Square Inner Cap (9)
into the top of each Vertical Tube (1).
21” Dumbbell Storage Rack
Note: The warning decal to the right
was placed on the rack. If the decal is
missing, please call our Customer
Service Department toll-free at 1-800-
322-2211, Monday through Friday, 6
a.m. until 6 p.m., Mountain Time, to
order a free replacement decal.
If you have questions, or if there are missing parts,
PLEASE CALL DIRECT TO OUR TOLL-FREE CUS-
TOMER HOT LINE. The trained technicians on our
customer hot line will provide immediate assistance.
Assembly Instructions
WARNING: To reduce the risk of seri-
ous injury, read the following precautions before
using the rack.
1. Inspect and tighten parts often. Replace worn
parts immediately.
2. Keep children under the age of 12 and pets
away from the rack at all times.
3. The rack is intended for home use only. Do not
use the rack in a commercial, rental, or institu-
tional setting.
4. The rack is designed to support a maximum
300 pounds of weights (not included).
5. Locate the warning decal on the rack, and
read the warnings before using the rack.
6. Use the rack only on a level surface. Cover
the floor beneath the rack to protect the floor.
7. Always place the heaviest weights on the bot-
tom rack.
CUSTOMER HOT LINE:
1-800-322-2211
Mon.–Fri., 6 a.m.–6 p.m. MST
8
8
2
2
8
6
9
9
3
3
6
6
7
6
5
5
6
7
6
8
1
1
6
4
5
4
5
4
5
4
5
Designed and distributed by WEIDERCARE,
a division of ICON Health & Fitness, Inc.

Weider 21 Dumbell Storage Rack Specifications

General

Color	Black
Assembly Required	Yes
Type	Dumbbell Rack
Capacity	21 Dumbbells
Number of Dumbbell Slots	21
Material	Steel

Summary

Safety and Warnings

General Safety Precautions

Crucial safety guidelines to reduce the risk of serious injury before using the rack.

Customer Service Hotline

Contact number for immediate assistance with product questions or missing parts.

Assembly Instructions

Step 1: Attach Outer Caps

Press 50mm Square Outer Caps onto each end of the two Frames.

Step 2: Attach Vertical Tubes

Attach Vertical Tubes to Frames using M8 bolts, washers, and locknuts.

Step 3: Attach Lower Racks

Mount the first Rack to the lower holes in Vertical Tubes with hardware.

Step 4: Attach Upper Racks

Mount the second Rack to the upper holes in Vertical Tubes with hardware.

Step 5: Insert Inner Caps

Insert 50mm Square Inner Caps into the top of each Vertical Tube.

Warning Decal Note

Information on the product's warning decal and how to order a free replacement.

Parts Information

Part List and Exploded Drawing

Detailed list and visual representation of all components for the dumbbell storage rack.

Ordering Replacement Parts

Instructions for ordering replacement parts by contacting the Customer Service Department.

Limited Warranty

Warranty Terms and Conditions

Details the 90-day warranty, coverage, limitations, exclusions, and consumer rights.