weintek MT-6056i User Manual

MT-600/8000 series
MT-6056i
Installation Instruction
0
1.0 Installation and Startup Guide
7
Install Environment
Where
Used
The MT-600/8000 Series is designed for industrial. The temperature range of operating
is from 32 to 113 °F (0 to 45 °C), as majority of industrial environments. It may not be
suitable for using in certain outdoor applications. Please consult the factory for
advised usage in outdoor applications.
NEMA
Rating
The MT-600/8000 Series front bezel is NEMA 4 rated. When installed properly in a
NEMA 4 panel, the NEMA 4 rating of the panel will not be compromised. This means
that fluids will not enter the panel during wash downs.
Electrical
Environment
The MT-600/8000 Series has been tested to conform to European CE requirements.
This means that the circuitry is designed to resist the effects of electrical noise. This
does not guarantee noise immunity in severe cases. Proper wire routing and
grounding will insure proper operation.
Mechanical
Environment
Avoid installing units in environments where severe mechanical vibration or shocks
are present.
1
2.0 Installation Instructions
4
2.1 Mounting Instructions
8
2.1.1 Location Considerations
Care should be taken when locating equipment behind the unit to ensure that AC power wiring, PLC
output modules, contactors, starters and relays, and any other source of electrical interference are located
away from the back of the unit.
Particular note should be taken to the position of variable speed drives and switching power supplies.
Their input and load cables should be screened to a central star earth point.
1

weintek MT-6056i Specifications

General

Display Type	TFT LCD
Touch Type	Resistive
Power Input	24V DC
Enclosure	Plastic
Humidity	10% to 90% (non-condensing)
Display Size	5.6 inches
Operating Temperature	0°C to 50°C
Storage Temperature	-20°C ~ 60°C
Weight	0.6 kg
Protection Rating	IP65
Resolution	320 x 234 pixels
USB	1 x USB 2.0 Host

Summary

Installation and Startup Guide

Install Environment

Details environmental requirements, including temperature, NEMA rating, and electrical/mechanical conditions, for optimal operation.

Installation Instructions

Mounting Instructions

Covers physical mounting aspects, location considerations, and NEMA-4 panel preparation for secure installation.

Power Connections

Explains DC power requirements, voltage range, input power, fusing, and high voltage cautions for safe electrical hookup.

Grounding Requirements

Details chassis ground usage, DC negative return connection, and optimal conductor sizing for system grounding.

Safety Guidelines

Presents recommended installation practices and procedures, emphasizing potential hazards and operator safety.

Programming Considerations

ICS Safety Recommendations

Discusses safety hazards in programmable control systems, including precautions and ICS Safety Recommendations.

Communications Connections

Connector COM1 [RS232]

Details cable requirements, pin assignments, and cautions for connecting via the COM1 RS232 port.

Connector COM1 [RS485]

Lists pin assignments and details for the COM1 RS485/422 communication port.

USB Ports

Covers USB Host (mouse, keyboard, drive) and USB Client (project download) port functionality and usage.

Dip Switch Settings

Explains the function of DIP switches for modes like Touch Screen Calibration, System Setting Bar, and Boot Loader.

CE Requirements

EU Directives and Standards

Details the EU directives and standards the MT-600/8000 series complies with, focusing on EMC and safety.

Specifications

Hardware Specifications

Lists technical hardware details including display, brightness, color, touch panel, I/O ports, processor, and memory.

General Specifications

Provides general operational parameters such as input power, operating temperature, humidity, enclosure, and dimensions.

Dimensions of MT-6056i

Front, Bottom, and Rear Views

Illustrates the physical dimensions and layout of the MT-6056i from front, bottom, and rear perspectives.

Panel Cutout Dimensions

Specifies the required cutout dimensions for panel mounting, ensuring proper fit and installation.