WESTENDORF MAX440 - User Manual

Questions and Answers

L
Leslie OrozcoAug 14, 2025
Why is my WESTENDORF Front End Loader operating slowly?
- M
  Michael NavarroAug 15, 2025
  Slow operation of your WESTENDORF Front End Loader can stem from several causes: * Insufficient oil supply. * Using oil with excessively heavy viscosity. * A clogged oil filter. * Malfunctioning hydraulic pump. * Air trapped within the hydraulic system. * Internal cylinder leakage. * A faulty valve. * Slow engine speed. * Hydraulic couplers not fully connected. To address this, verify the oil level, switch to oil with the correct viscosity, clean or replace the oil filter, repair or replace the hydraulic pump, locate and fix any leaks, cycle all cylinders to remove air, install a seal repair kit, repair or replace the signal line, increase the engine speed, and check the hydraulic couplers.
W
wlawsonAug 18, 2025
What to do if WESTENDORF Front End Loader cannot lift load?
- S
  Steven NormanAug 18, 2025
  If your WESTENDORF Front End Loader is unable to lift a load, the possible causes include a low oil supply, low oil pressure, worn lift cylinders, a malfunctioning hydraulic pump, or an excessive load. To resolve this, first check the oil level and the oil pressure at the tractor valve. If the oil pressure is low, consult the "Hydraulic System Troubleshooting" section for further guidance. Test the lift cylinders by raising the loader 6-8 feet off the ground and disconnecting the hydraulics at the couplers; if the loader settles, there's likely an internal leak, requiring a seal repair kit. You may also need to repair or replace the hydraulic pump or reduce the load.
K
Katie LucasAug 21, 2025
Why does my WESTENDORF Front End Loader jerk when raising or lowering?
- M
  Michael McbrideAug 21, 2025
  If your WESTENDORF Front End Loader jerks, chatters, or vibrates when raising or lowering, it could be due to air in the hydraulic system, low oil supply, a plugged oil filter, a malfunctioning hydraulic pump, or disconnected auxiliary valve lines. To fix this, locate and repair any leaks, cycle all cylinders several times to remove air from the system, check the oil level, clean or replace the oil filter, and repair or replace the hydraulic pump. Also, consult your manual for additional guidance.
M
Michael Mitchell Jr.Aug 25, 2025
How to fix WESTENDORF Front End Loader that won't raise or lower?
- P
  patriciahernandezAug 25, 2025
  If your WESTENDORF Front End Loader isn't raising or lowering, it could be due to an incomplete hydraulic circuit, hoses not fully or incorrectly connected, unmatched or defective couplers, or a damaged signal line (if it's an auxiliary hydraulic system). Check all hose connections, ensuring they are properly connected. Repair or replace any defective couplers. You may also need to repair or replace the signal line or remove the suction hose.
H
hamiltonmichelleAug 28, 2025
What to do if my WESTENDORF Front End Loader slowly leaks down?
- D
  Denise SimmonsAug 28, 2025
  If your WESTENDORF Front End Loader slowly leaks down, it may be caused by external oil leaks, internal cylinder leaks, a worn control valve, damaged O-rings, or improperly adjusted valve cables. To address this, start by tightening any loose fittings and applying thread sealer on pipe threads. Test the lift cylinders by raising the loader 6-8 feet off the ground and disconnecting the hydraulics at the tractor; if the loader settles, there is an internal leak and you should install a seal repair kit. Also, repair or replace the control valve, replace O-rings, and adjust the cables.
A
Amanda OconnellAug 31, 2025
Why is the bucket on my WESTENDORF Front End Loader not level?
- B
  Brian Shaffer MDAug 31, 2025
  If the bucket on your WESTENDORF Front End Loader is not level from side to side, it could be due to rear tires not being equally inflated, mounting brackets not being level, or damaged bucket mounts. Make sure to inflate all tires to the correct pressure, adjust the mounting brackets, and repair the bucket mounting attachment.
K
Krista RileySep 3, 2025
What causes inconsistent WESTENDORF Front End Loader movement?
- S
  Sheryl JacksonSep 4, 2025
  Inconsistent movement of your WESTENDORF Front End Loader in relation to the control lever is often due to cable adjustment issues. Correct adjustment of the cables is necessary to resolve this.
A
Amy BurnsSep 7, 2025
What causes loss of bucket tilt control in WESTENDORF Front End Loaders?
- M
  Michelle MorenoSep 7, 2025
  Loss of bucket tilt control when the lever is pushed completely forward on your WESTENDORF Front End Loader can occur if the control lever is in the "float" position or if there's a float issue on the lift spool. Use the "float" lockout feature to keep the control lever out of the "float" position. Also, check the correct connection.
M
Mark BushSep 12, 2025
Why is my WESTENDORF Front End Loader contacting tie rods?
- U
  ujohnsonSep 12, 2025
  If your WESTENDORF Front End Loader is contacting the tie rods, it's likely because the axle stops are not installed or the tires are not set out equally. Install the axle stops and move the tires out to their recommended settings.