9 Parameter setting9 Parameter setting
If the Voltage Ramp mode is selected, the flow chart of the related
parameters setting is show in figure 9-2
If the Voltage Ramp mode is selected, the flow chart of the related
parameters setting is show in figure 9-2
9.2 (Voltage Ramp mode) Setting and Inquiry9.2 (Voltage Ramp mode) Setting and Inquiry
9.1 Starting mode9.1 Starting mode
User ManualUser Manual User ManualUser Manual
18
OPERATION
MENU
19
OPERATION
MENU
On Ready state , press key and release it 5 minutes later ( or
press and key at the same time), system enter the Starting mode
selecting state . Then press or key to modify the parameter
to set the Starting Mode Code . If 1 is selected, the lamp on the
top-left of the keyboard Voltage Ramp is light , the Starting mode is
Voltage Ramp. If 2 is selected, the lamp on the top-left of the
keyboard Current Limit is light, the Starting mode is Current Limit.
If 3 is selected, the Starting Mode is Jogging. Any lamp on the left of
keyboard is not light. After the starting mode parameter is selected, press
key, other parameter related to the selected Starting mode can be
modified.
On Ready state , press key and release it 5 minutes later ( or
press and key at the same time), system enter the Starting mode
selecting state . Then press or key to modify the parameter
to set the Starting Mode Code . If 1 is selected, the lamp on the
top-left of the keyboard Voltage Ramp is light , the Starting mode is
Voltage Ramp. If 2 is selected, the lamp on the top-left of the
keyboard Current Limit is light, the Starting mode is Current Limit.
If 3 is selected, the Starting Mode is Jogging. Any lamp on the left of
keyboard is not light. After the starting mode parameter is selected, press
key, other parameter related to the selected Starting mode can be
modified.
For Example: For Example:
Voltage Ramp Voltage Ramp
Current LimitCurrent Limit
JoggingJogging
Press
(maintain 5 second)
Press
(maintain 5 second)
Or press Or press
press or press or
Starting mode Starting mode
Figure 9-1
Note:
User can select the Starting mode according to the load type. For the normal load,
any of two modes can be adopted. But for big inertia load type, the Voltage Ramp
mode is the best choice. The default value is , that is Voltage Ramp mode.
Note:
User can select the Starting mode according to the load type. For the normal load,
any of two modes can be adopted. But for big inertia load type, the Voltage Ramp
mode is the best choice. The default value is , that is Voltage Ramp mode.
PressPress
Voltage Ramp modeVoltage Ramp mode
Initial voltage of rampInitial voltage of ramp
PressPress
PressPress
PressPress
PressPress
PressPress
PressPress
PressPress
PressPress
Start time of rampStart time of ramp
Over current protect valueOver current protect value
Current unbalance factorCurrent unbalance factor
Control mode selectControl mode select
SCR trigger selectSCR trigger select
Start overload levelStart overload level
Over current protect at runningOver current protect at running
Stop mode selecStop mode selec
PressPress
Soft stop
factor
Soft stop
factor
PressPress
to modifyto modify
oror
PressPress
to modifyto modify
oror
PressPress
to modifyto modify
oror
PressPress
to modifyto modify
oror
PressPress
to modifyto modify
oror
PressPress
to modifyto modify
oror
PressPress
to modifyto modify
oror
PressPress
to modifyto modify
oror
PressPress
to modifyto modify
oror
PressPress
to modifyto modify
oror
PressPress
Figure 9-2
Note:
1. When any of one parameter is modified, press whether key (change page)
or key( return Ready state ), the modified parameters will be saved
automatic.
2. When modify any of the parameter, press key to return the Ready state
Note:
1. When any of one parameter is modified, press whether key (change page)
or key( return Ready state ), the modified parameters will be saved
automatic.
2. When modify any of the parameter, press key to return the Ready state
To Next Page
Loading...
Need help?
General
