What to do if Whirlpool AMD 091/1 runs, but does not cool or heat?
If your Whirlpool Air Conditioner is running but not cooling or heating, first check the filter to ensure it is clean and not blocked by debris. Also, make sure the air outlet isn't blocked. Finally, verify that the set temperature is appropriate: lower it in cooling mode or raise it in heating mode.
How to troubleshoot a Whirlpool AMD 091/1 that does not turn on?
There are several reasons why your Whirlpool Air Conditioner might not be operating. Ensure the power cord is plugged into a grounded outlet. Check if a household fuse has blown or a circuit breaker has tripped, and replace the fuse or reset the breaker if necessary. Make sure the On/Off button has been pressed. If there's a local power failure, wait for the power to be restored. Also, verify that you're using the correct time-delay fuse or circuit breaker capacity and replace it if needed.
What to do if Whirlpool AMD 091/1 runs for a short time only, but room is not cool or hot?
If your Whirlpool Air Conditioner runs only briefly and the room doesn't cool or heat adequately, the set temperature might be too close to the current room temperature. Try lowering or raising the set temperature.
Why does my Whirlpool AMD 091/1 keep blowing fuses?
If your Whirlpool Air Conditioner is blowing fuses or tripping circuit breakers, it could be due to several reasons. Too many appliances might be sharing the same circuit; try unplugging or relocating some of them. Also, avoid restarting the air conditioner immediately after turning it off; wait at least 3 minutes. Changing modes can also cause this issue, so allow the unit to rest for 3 minutes before restarting after a mode change.
Why is my Whirlpool Air Conditioner running so much?
If your Whirlpool Air Conditioner seems to run constantly, check for open doors or windows and ensure they are closed. In cooling mode, the unit might be working harder in a heavily occupied room or if heat-producing appliances are in use. Try using exhaust fans while cooking or bathing and avoid using heat-producing appliances during the hottest part of the day. Remember that local air conditioners provide supplemental cooling. In heating mode, the unit might be in a very cool room, and a higher capacity air conditioner might be necessary.
Why does my Whirlpool AMD 091/1 cycle on and off so much?
If your Whirlpool Air Conditioner cycles on and off too frequently, it might not be the right size for the room. Also, a dirty or obstructed filter can cause this issue, so clean the filter. In cooling mode, excessive heat or moisture in the room (from cooking or showers) can cause cycling; use a fan to exhaust the heat or moisture. In heating mode, the environment's temperature might be too high; avoid using the air conditioner in such conditions. Ensure the louvers are not blocked by curtains, blinds, or furniture. Finally, avoid operating the air conditioner in cooling mode if the outside temperature is below 18°C.
Guidelines for safe operation and health advisories regarding direct cool air exposure.
Information on environmental protection and responsible disposal practices.
Proper disposal procedures for the appliance according to WEEE directive.
Instructions for recycling and disposing of packaging materials.
Instructions for inserting batteries into the remote control.
Steps for safely removing batteries from the remote control.
Guidance on proper disposal of used batteries.
Details on Cooling, Dry, Fan Only, and Heating modes.
Procedure to reset the filter indicator light after cleaning.
Instructions for setting the desired temperature.
How to choose and set the fan speed.
How to set and adjust the real-time clock.
Instructions for setting the on/off timer for the appliance.
Procedure to cancel the scheduled timer.
Instructions for switching the appliance on and off.
How to choose different operational modes using the remote.
Automatic mode adjusting settings by room temperature.
Feature for rapid cooling.
How to select and adjust fan speed.
Process to adjust the desired temperature.
How the U button on the remote control works.
Instructions for activating and using the sleep mode.
How to adjust vertical airflow direction using the remote or panel.
Description of typical operating sounds from the air conditioner.
Procedure for draining accumulated water from the unit.
Steps for removing, cleaning, and reinstalling the air filter.
Instructions for cleaning the exterior surfaces of the unit.
Guidance on preparing and storing the unit after use.
Analysis and solutions for issues like unit not operating or tripping breakers.
Troubleshooting for problems like running too much or not cooling/heating.
Solutions for cycles on/off too much or short run times.
Guidelines for proper placement and ventilation.
Specifications for power connection and circuit protection.
Instructions for connecting and handling the power cord.
Steps for removing and cleaning packaging materials.
Procedure for connecting the exhaust hose to the unit and window.
Troubleshooting steps to attempt before calling for service.
Information required when reporting a fault or requesting repair.
General| Connected load | - W |
|---|---|
| AC input voltage | 220-240 V |
| AC input frequency | 50 Hz |
| Energy efficiency class (cooling) | A |
| Energy efficiency class (heating) | - |
| Hourly energy consumption (cooling) | 1.1 kWh |
| Hourly energy consumption (heating) | - kWh |
| Type | Monobloc mobile air conditioner |
| Filter type | Polyethylene terephthalate (PET) |
| Noise level | 65 dB |
| Remotely operated | Yes |
| Refrigerating medium | R410A |
| Cooling capacity (max) | - BTU/h |
| Air conditioner functions | Cooling, Dehumidifying, Fan, Heating |
| Cooling capacity in watts (max) | 2840 W |
| Cooling energy efficiency (EER, W/W) | 2.6 |
| Product color | White |
Weight and Dimensions| Depth | 360 mm |
|---|---|
| Width | 460 mm |
| Height | 840 mm |
| Weight | 36000 g |
To Next Page