To Next PageTo Next PageWhy is my Whirlpool AMD 312 Air Conditioner not cooling or heating?
Several factors could be the cause. It could be that the air filter is dirty, or the air intakes and outlets are blocked. The temperature might not be set properly as well.
What to do if my Whirlpool Air Conditioner does not run?
Your Whirlpool Air Conditioner may not be running due to a blown protection device or fuse. In this case, wait for 3 minutes and try starting it again, as the protection device might be preventing the unit from working. Also check if the RC batteries are low, or if the plug is not properly plugged.
Why is the control of my Whirlpool Air Conditioner ineffective?
If you're experiencing ineffective control with your Whirlpool Air Conditioner, it might be due to strong interference, such as excessive static electricity discharge or power supply voltage abnormality. If this happens, unplug the unit from the power supply and plug it back in after 2-3 seconds.
Why my Whirlpool AMD 312 does not operate immediately?
A 3-minute delay will occur when changing the mode during operation of your Whirlpool Air Conditioner.
Why does mist spray from the outlet of my Whirlpool AMD 312?
The mist spraying from the outlet of your Whirlpool Air Conditioner is normal if it's present in a room with low temperature. This happens because of the cool air discharged from the indoor unit during COOLING or DRY operation mode.
Why does my Whirlpool AMD 312 have a peculiar smell?
The peculiar smell coming from your Whirlpool Air Conditioner may originate from another source, such as furniture or cigarette smoke, which is drawn into the unit and expelled with the air.
Why does my Whirlpool AMD 312 make a sound of running water?
The sound of running water in your Whirlpool Air Conditioner is normal. It's caused by the flow of refrigerant within the system or could be a defrosting sound in heating mode.
Why is my Whirlpool Air Conditioner making a cracking sound?
The cracking sound you hear from your Whirlpool Air Conditioner may be generated by the expansion or contraction of the front panel due to temperature changes.
General| Energy Efficiency Rating | 3 Star |
|---|---|
| Compressor Type | Rotary |
| Energy Efficiency Ratio (EER) | 3.1 |
| Operating Frequency | 50 Hz |
| Type | Split AC |
| Refrigerant | R32 |
| Dimensions | Outdoor Unit: 780 x 540 mm |
| Weight | Indoor Unit: 9 kg |
| Operating Voltage | 220-240 V |
Instructions for setting the remote control's initial mode.
How to set and cancel the auto-restart feature on the indoor unit.
Information on recycling the product's packaging materials.
Guidance on how to correctly dispose of the appliance.
Identification of parts like air intake, display, and control buttons.
Identification of parts like air intake, outlet, and connection cords.
Details on the meaning of temperature, running, timer, sleep, and compressor indicators.
Explanation of functions like ON/OFF, Mode, Fan, Sleep, Jet, and Swing buttons.
Visual representation and meaning of symbols shown on the remote control screen.
Guidance on inserting, removing, disposing of batteries, and general remote care.
Sequence for changing modes like Cooling, Dry, Fan Only, and Heating.
How to adjust fan speed and its behavior in different modes.
How to adjust the desired temperature and available ranges.
Steps to start the appliance using the remote control.
Using the remote control's SWING button for automatic louvre movement.
Manual adjustment of horizontal louvers using control rods.
How the unit automatically adjusts settings based on room temperature.
Step-by-step guide to setting on-timers and off-timers.
Procedures for cleaning the front panel and general unit care.
Steps for removing, cleaning, and refitting the air filter.
Conditions like temperature limits that trigger protective stops.
Advice on installation to minimize noise and avoid disturbing neighbours.
Visual representation of recommended clearances and placement for units.
Criteria for selecting the best position for the indoor unit.
Criteria for selecting the best position for the outdoor unit.
How to attach the mounting plate securely to the wall.
Drilling the wall and installing a sleeve for the piping.
Connecting pipes and cables to the indoor unit base.
Details on applying insulation material to pipes and hoses.
How to connect power cables to both indoor and outdoor units.
Details on power and connecting cable types and their cross-sectional areas.
Schematic illustrating the electrical connections between indoor and outdoor units.
Attaching the drain port and hose for condensate water in heating mode.
Connecting the refrigerant pipes to the outdoor unit's valves.
Procedure for removing air and moisture from the refrigeration cycle using a vacuum pump.
