To Next PageTo Next PageWhat to do if my Whirlpool Air Conditioner is not cooling or heating air?
If your Whirlpool Air Conditioner isn't cooling or heating, check if the air filter is dirty. Also, make sure that the intakes and outlets of the unit are not blocked. Finally, verify that the temperature is set properly.
What to do if my Whirlpool AMD 302 Air Conditioner does not run?
If your Whirlpool Air Conditioner does not run, check if the protection device or fuse has blown. Wait 3 minutes before restarting, as the protection device may be preventing operation. Also, check the remote control batteries and ensure the unit is properly plugged in.
What to do if my Whirlpool AMD 302 control is ineffective?
If you experience ineffective control of your Whirlpool Air Conditioner, it might be due to strong interference such as excessive static electricity discharge or power supply voltage abnormality. Unplug the unit from the power supply and re-plug it after 2-3 seconds.
Why does my Whirlpool AMD 302 Air Conditioner indoor unit fan stop during heating?
The indoor unit fan may stop during heating because the Whirlpool Air Conditioner is de-icing, which can take up to 10 minutes. This typically occurs when the outdoor temperature is very low and humidity is high. The unit will automatically resume operation after approximately 10 minutes.
Why does my Whirlpool AMD 302 make a sound of running water?
A sound of running water in your Whirlpool Air Conditioner is normal and is caused by the flow of refrigerant within the system. It can also be a defrosting sound when the unit is in heating mode.
Why does my Whirlpool Air Conditioner mist spray from the outlet?
If you notice mist spraying from the outlet of your Whirlpool Air Conditioner, especially in a room with low temperature, it's normal. This occurs due to cool air discharged from the indoor unit during COOLING or DRY operation mode.
Why does my Whirlpool AMD 302 make a cracking sound?
The cracking sound in your Whirlpool Air Conditioner may be generated by the expansion or contraction of the front panel due to temperature changes.
What to do if my Whirlpool AMD 302 does not operate immediately?
A 3-minute delay will occur when changing mode during operation of your Whirlpool Air Conditioner.
What to do if, after switching off, the flap of my Whirlpool AMD 302 appears not to close fully?
If, after switching off your Whirlpool Air Conditioner, the flap does not close fully, it may be because the stepping motor could not find the RESET point. Try restarting the air conditioner and then stopping it again.
Why does my Whirlpool AMD 302 Air Conditioner have a peculiar smell?
The peculiar smell from your Whirlpool Air Conditioner may originate from external sources like furniture or cigarette smoke, which are drawn into the unit and expelled with the air.
General| Brand | Whirlpool |
|---|---|
| Model | AMD 302 |
| Category | Air Conditioner |
| Language | English |
Presetting the remote control for heat pump mode and its implications.
Setting and cancelling the auto-restart function on the indoor unit.
Packaging is 100% recyclable. Dispose according to local regulations.
Appliance marked by WEEE directive. Dispose correctly to prevent harm.
Lists and illustrates parts of both indoor and outdoor units.
Explains various indicator lamps and displays on the unit.
How to use the emergency switch for operation.
Details on various buttons and indicators on the remote control.
Step-by-step guide for inserting batteries correctly.
Instructions for safely removing batteries from the remote.
Proper disposal methods for used batteries.
Restores previous settings after a power cut.
Description of the cooling mode operations.
Description of the dry mode operations.
Description of the fan-only mode operations.
Description of heat pump mode operations.
How sleep mode adjusts temperature and fan speed.
Conditions for defrosting activation and termination.
Description of the rapid cooling (JET) mode.
Steps for setting up timer functions.
Details on setting timer on, timer off, and combined timers.
Instructions for cleaning the front grille and air filters.
Steps for preparation before long-term storage.
Actions to take after a long period of non-use.
Common issues and their potential causes and solutions.
Conditions that necessitate calling a service center.
How to attach the mounting plate securely.
Instructions for drilling wall holes for installation.
Steps for connecting electrical wiring.
How to route the pipes based on unit output.
Procedure for repositioning the drain hose.
Attaching the indoor unit to the mounting plate.
Correct and incorrect methods for drain hose setup.
How to seal wall openings and fasten pipes.
Steps for wiring the outdoor unit for specific models.
How to connect the pipe joint.
Steps for removing air from the refrigerant lines.
Process for expanding pipe orifices.
Guidelines for adding refrigerant based on pipe length.
Testing operation via the emergency switch.
Testing operation using the remote control.
Verifying system operation via indicator lamps.
