Whirlpool AMD 385 User Manual (English)

Questions and Answers:

S
Samuel NicholsonAug 17, 2025
Why is my Whirlpool AMD 385 not cooling or heating properly?
- R
  Robert WarrenAug 17, 2025
  If your Whirlpool Air Conditioner isn't cooling or heating correctly, consider these points: * Ensure the temperature is set correctly. * Check for any blockages of the air intake or outlet on the outdoor unit and clear them. * Clean the air filter if it's clogged with dust. * Confirm that all doors and windows are closed. * Adjust the airflow if it's set to "LOW FAN." * Remove or reduce any other heat sources in the room.
W
wallacenicholasAug 19, 2025
What to do if the Whirlpool AMD 385 remote control is not working?
- Z
  zcaldwellAug 19, 2025
  If your Whirlpool Air Conditioner remote control isn't working, try these steps: * Switch the air conditioner off and on again. * Ensure the remote control is within range and there are no obstructions. * Replace the battery if it's low. * Inspect the remote control for any damage.
A
Ashlee DurhamAug 22, 2025
What to do if my Whirlpool AMD 385 Air Conditioner does not run?
- S
  Stephanie WilliamsAug 22, 2025
  If your Whirlpool Air Conditioner isn't running, check the following: * Ensure there isn't a power failure by checking the power supply. * Make sure the power plug is securely in the socket. * Reset the circuit protection device if it has been tripped. * Have a professional test the voltage if you suspect it's too high or low. * Verify that the timer function is correctly set.
D
davidhughesAug 26, 2025
How to get rid of the bad smell from my Whirlpool AMD 385 when I turn it on?
- K
  Kenneth EdwardsAug 26, 2025
  If you notice an unpleasant odor when starting your Whirlpool Air Conditioner, it could be due to odors accumulated from the environment. Clean the air filter. If the problem persists, the air conditioner should be cleaned (Please contact the Whirlpool Authorized Service Centre).
C
cherylmillerAug 28, 2025
Why is my Whirlpool Air Conditioner leaking water inside?
- F
  felicia47Aug 28, 2025
  Water leaks from the indoor unit of your Whirlpool Air Conditioner can be due to high air humidity, condensation overflow, or a loose joint on the indoor unit's drain pipe. Tighten the joint of the drain pipe.
G
gilbertsusanAug 30, 2025
Why does my Whirlpool Air Conditioner not start right away after I turn it off?
- J
  Joshua PhillipsAug 30, 2025
  To protect the air conditioner when started after a stop, the microcomputer control delays for 3 minutes before allowing the air conditioner to start. Wait for 3 minutes after stopping before starting the air conditioner.
C
caldwellmistySep 2, 2025
Why is there fog coming out of my Whirlpool Air Conditioner?
- A
  Ashley Powers MDSep 2, 2025
  A thin fog may flow from the outlet of your Whirlpool Air Conditioner when it's running in cooling mode if the indoor temperature and humidity are high. After a short time, the fog will disappear as the indoor temperature and humidity decrease.
M
Maurice AcevedoSep 5, 2025
Why is my Whirlpool Air Conditioner leaking water outside?
- R
  robin34Sep 5, 2025
  Water leaks from the outdoor unit of your Whirlpool Air Conditioner can occur for several reasons. In cooling mode, water may condense on the pipe or pipe joint due to cooling. Defrost water flows out in heating or defrost (auto defrost) mode. In cooling mode, water from the heat exchanger may leak.
T
Tanya LoveSep 8, 2025
Why does my Whirlpool AMD 385 make a cracking noise when starting or stopping?
- J
  Jonathon SimsSep 8, 2025
  The slight crack you hear when your Whirlpool Air Conditioner starts or stops is the sound of friction caused by the expansion of the front panel or other parts due to temperature changes.
B
Beth ChoiSep 12, 2025
Why does my Whirlpool AMD 385 Air Conditioner make noise?
- B
  Benjamin MeyerSep 12, 2025
  The noise from the indoor unit of your Whirlpool Air Conditioner can be due to the fan or compressor relay switching over (close/open). The air conditioner may also make noise in defrost mode or when stopped due to inverse flow of refrigerant in the unit.