Whirlpool FWEB9002IG - Factory Test Mode Operation

17
序
号
Wat
er
heat
ing
pipe
L
Wate
r
heati
ng
pipe
L
Water
heatin
g pipe
L
L+
N
Heati
ng
pipe
for
dryin
g
Main
Wate
r
inflo
w
Sof
ten
er
infl
ow
Defo
am
inflo
w
Dehu
midif
icati
on
inflo
w
Wate
r
drain
valve
open
ed
Drai
nage
valve
and
pum
p
close
d
Door
lock
ozon
e
Dryi
ng
Fan
Spra
ying
&
sprin
kling
inflo
w
Motor washing
0
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ● ○ ○ ○
Forward/revers
e rotation
4s On -
2s Off
1
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ● ○ ○ ○
2
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ● ○ ○ ○
3
○ ○ ● ○ ○ ○ ○ ○ ○ ○ ● ○ ○ ○
4
○ ○ ○ ● ○ ○ ○ ○ ○ ○ ● ○ ○ ○
5
○ ○ ○ ○ ● ○ ○ ○ ○ ○ ● ○ ○ ○
6
○ ○ ○ ○ ○ ● ○ ○ ○ ○ ● ○ ○ ○
7
○ ○ ○ ○ ○ ○ ● ○ ○ ○ ● ○ ○ ○
8
○ ○ ○ ○ ○ ○ ○ ● ○ ○ ● ○ ○ ○
9
○ ○ ○ ○ ○ ○ ○ ○ ● ○ ● ○ ○ ○
10
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ● ○ ○ ○
11
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ● ○ ○ ○
12
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ● ○ ● ○
13
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ● ○ ○ ○
End
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Off
During the test, the first digit in the LCD shows the serial number. Motor rotates forward / reverse in the inspection process.
When the test is finished, the LCD shows "End"
If any fault is detected, LCD will display the fault code. After the detection process, turn off the power.
Note: the heat-drying tube, drying fan, dehumidification inflow are only subject to models with the drying function.
6.3 Factory test mode
Turn on the power, press and hold the "Program (SW8)" key and press the "Start/pause
(SW2)" key for three times under the mixed washing procedure, then the buzzer will prompt
to enter the factory inspection mode.
Display Content
Remark
Model No.
100
Press " Rinse " button Model No.
ITE and D (for Whirlpool) switch display
Press " Rinse " button Function Information
B(single washing model)/BH (drying) and
UP(upper drainage) switching display
Press " Rinse " button Version information
A represents the version number
Press " Rinse " button Version information
B represents Inverter version number
Press " Rinse " button Version information
C represents main control version number