Whirlpool TDLR70112 - User Manual

Questions and Answers

M
Mary GarciaAug 12, 2025
How to fix Whirlpool Washer that won't turn on?
- D
  Daniel CooperAug 12, 2025
  If your Whirlpool Washer isn't turning on or the program isn't starting, here are a few things to check: * Ensure the plug is fully inserted into the electrical outlet. * Verify there hasn't been a power failure. * Make sure the lid is properly closed. * Check if the “Child lock“ function is activated (if available). * The washer may have automatically switched off to save energy. To turn it back on, turn the program selector to “Of/fO” and then select your desired program again.
H
Heidi LawsonAug 15, 2025
Why won't the wash cycle start on my Whirlpool TDLR70112?
- J
  Jessica HernandezAug 16, 2025
  If the wash cycle on your Whirlpool washer isn't starting, make sure that you have pressed the “Start/Pause“ button, the water tap is open, and a “Start delay“ has not been set.
P
paula20Aug 20, 2025
Why does my Whirlpool TDLR70112 Washer vibrate so much?
- C
  candicebradshawAug 20, 2025
  If your Whirlpool washer vibrates, make sure that the washing machine is level and that the transport bracket has been removed before using the washing machine.
J
Jonathan SimpsonAug 23, 2025
What to do if “Clean pump“ indicator lights up on Whirlpool TDLR70112?
- M
  miranda93Aug 23, 2025
  If the “Clean pump“ indicator lights up on your Whirlpool Washer, it means waste water is not being pumped out. To resolve this, clean the water filter.
F
Frank MooreAug 27, 2025
Why are my Whirlpool TDLR70112 Washer final spin results poor?
- R
  Robert ButlerAug 27, 2025
  If the final spin results of your Whirlpool washer are poor and the laundry is still very wet, and the “Spin/Drain“ indicator blinks, or the spin speed on the display blinks, or the spin speed indicator blinks after the end of the programme, it could be due to an unbalance of the laundry load during spinning, which prevented the spin phase to avoid damages on the washing machine. This can happen with small laundry loads (consisting of only few quite big or absorbent items, e.g. towels), or big/ heavy laundry items. If possible avoid small laundry loads. Check if the “Spin“ button has been set to a low spin speed.
B
Brian TuckerAug 30, 2025
Why does the “Water tap closed“ indicator light up on my Whirlpool TDLR70112 Washer?
- J
  Jill JonesAug 30, 2025
  If the “Water tap closed“ indicator lights up on your Whirlpool Washer, it means the appliance has no or insufficient water supply.
P
Paul ZamoraSep 4, 2025
What does “Detergent over dosage“ mean on Whirlpool Washer?
- P
  Paul VazquezSep 4, 2025
  If the “Detergent over dosage“ indicator lights up on your Whirlpool Washer, it means that you used too much detergent, too much foam is formed, or the detergent is not compatible with the washing machine (it must bear the wording “for washing machines“, “for hand washing and washing machines“, or something similar).
W
William BoydSep 7, 2025
What to do if Whirlpool TDLR70112 Washer stops during the programme?
- T
  taylorbruceSep 7, 2025
  If your Whirlpool washer stops during the program and the “Start/Pause“ light is blinking, it could be because the “Rinse hold“ option is activated (if available) or the program has been changed. To fix this, re-select your desired program and press “Start/Pause“.