Whirlpool TDLR70123 - User Manual

Questions and Answers

E
Emily ThompsonAug 14, 2025
Why won't my Whirlpool Washer turn on?
- E
  Emily HaynesAug 14, 2025
  Your Whirlpool Washer might not turn on because the plug isn't fully inserted into the electrical outlet, there's a power failure, the lid isn't properly closed, the Child lock function is activated, or the washing machine switched off automatically to save energy. Ensure the plug is fully inserted, check the power supply, close the lid properly, deactivate the Child lock, or turn the programme selector first to “Of/fO” and then to the desired programme again.
L
lindsayjohnsonAug 17, 2025
Why are my Whirlpool Washer spin results poor?
- C
  Cynthia GravesAug 17, 2025
  Poor spin results in your Whirlpool washer, leaving laundry very wet, can occur due to an unbalance of the laundry load during spinning, small laundry loads, or the “Spin“ button being set to a low spin speed. Adjust the laundry load to ensure balance, avoid small laundry loads if possible, and set the “Spin“ button to a higher spin speed.
B
Brittany OconnorAug 21, 2025
What to do if my Whirlpool TDLR70123 is indicating an error code?
- Y
  yateslindaAug 21, 2025
  If your Whirlpool washer displays an error code (e.g. F-02, F-..), shut off the machine, disconnect the plug from the outlet, and wait about 1 minute before turning it back on.
M
Mary PatelAug 25, 2025
Why does my Whirlpool TDLR70123 Washer vibrate so much?
- B
  Brendan WardAug 25, 2025
  Your Whirlpool washer may be vibrating excessively because it is not level or because the transport bracket has not been removed. Level the washing machine and remove the transport bracket.
M
Monica MontgomeryAug 27, 2025
Why does the “Detergent over dosage“ indicator light up on my Whirlpool TDLR70123 Washer?
- C
  Charlotte DaviesAug 27, 2025
  The “Detergent over dosage“ indicator lights up on your Whirlpool Washer if you used too much detergent, too much foam is formed, or the detergent isn't compatible with the washing machine. Use less detergent, reduce the amount of detergent used, and use a compatible detergent.
R
Ricky BrownAug 30, 2025
Why does the “Clean pump“ indicator light up on my Whirlpool TDLR70123?
- S
  seanwaltonAug 30, 2025
  The “Clean pump“ indicator lights up on your Whirlpool washer because waste water is not being pumped out. Clean the water filter.
M
Misty ManningSep 3, 2025
What to do if my Whirlpool Washer cycle does not start?
- H
  Holly RamirezSep 3, 2025
  If the wash cycle on your Whirlpool washer doesn't start, it could be because the “Start/Pause“ button hasn't been pressed, the water tap isn't open, or a “Start delay“ has been set. Press the “Start/Pause“ button, open the water tap, or cancel the “Start delay“ setting.
W
William BrownSep 6, 2025
What to do if my Whirlpool TDLR70123 stops during the programme?
- S
  Stephanie RichardsSep 6, 2025
  If your Whirlpool appliance stops during the programme and the “Start/Pause“ light blinks, it might be because the “Rinse hold“ option is activated or the programme has been changed. Deactivate the “Rinse hold“ option or re-select the desired programme and press “Start/Pause“.
B
Brianna NealSep 10, 2025
Why does the “Water tap closed“ indicator light up on my Whirlpool TDLR70123 Washer?
- D
  Dale WolfeSep 10, 2025
  The “Water tap closed“ indicator lights up on your Whirlpool Washer because the appliance has no or insufficient water supply. Check the water supply.