Whirlpool WGT4027HW User Manual (English)

Other manuals for Whirlpool WGT4027HW

Questions and Answers:

R
robert39Aug 25, 2025
Why won't my Whirlpool WGT4027HW run or fill with water?
- G
  gonzalezstephanieAug 26, 2025
  If your Whirlpool Washer/Dryer won’t run or fill, stops working, or the wash light remains on, first ensure it's properly connected to a grounded outlet and receiving power, avoiding extension cords. The lid must be closed for the washer to operate. The washer will pause during certain phases of the cycle, so avoid interrupting it. If the load is unbalanced, remove some items and rearrange the load evenly in the basket, then close the lid and press the START/PAUSE button. Do not add more than one or two additional items after the cycle has started, and avoid adding extra water to the washer. If problems persist, it is recommended to contact an electrician.
G
George AndrewsAug 26, 2025
Why is the Lid Lock light flashing on my Whirlpool WGT4027HW?
- L
  Lisa DunnAug 27, 2025
  If your Whirlpool Washer/Dryer is showing a flashing Lid Lock light, ensure that the lid is completely closed, as the washer will not start with the lid open. If a cycle was stopped or paused, the lid will remain locked until the basket has completely stopped spinning, which may take several minutes, especially with large loads or heavy fabrics.
K
Karl BurkeAug 27, 2025
Why is my Whirlpool WGT4027HW using the wrong wash or rinse temperature?
- Y
  Yvonne HaleAug 28, 2025
  If you notice incorrect or wrong wash or rinse temperatures in your Whirlpool Washer/Dryer, start by checking that the hot and cold inlet hoses are not reversed and are properly attached to both the washer and faucet, ensuring both hot and cold water are flowing to the inlet valve. Also, make sure that the inlet valve screens are not clogged and that there are no kinks in the hoses. Note that this washer uses cooler wash and rinse water temperatures than your previous washer, including cooler hot and warm washes, as part of its energy-saving design.
J
Jacob CrawfordAug 29, 2025
Why are there dry spots on my Whirlpool WGT4027HW load after the cycle?
- C
  Christine FarmerAug 29, 2025
  If you find dry spots on your load after a cycle in your Whirlpool Washer/Dryer, it could be due to a few reasons. This washer uses less water than traditional top-load washers, so try washing a smaller load or running the Heavy Duty cycle. High spin speeds extract more moisture, which, combined with airflow, can cause dry spots on items near the top of the load; this is normal. If the washer is tightly packed, use the Bulky Items cycle for a higher water fill. Also, avoid adding extra garments after the sensing/fill phase, limiting it to only one or two additional garments.
S
Steven RandallAug 30, 2025
How to prevent my Whirlpool WGT4027HW load from tangling?
- F
  Fred GardnerAug 30, 2025
  If you're experiencing tangling with your Whirlpool Washer/Dryer, it could be related to how the washer is loaded. Refer to the “Using Your Washer” section for loading recommendations. Try selecting a cycle with a slower wash action and spin speed, though items will be wetter. Load garments in loose heaps evenly around the basket wall, and reduce tangling by mixing types of load items. Use the recommended cycle for the type of garments being washed.
I
ian99Aug 31, 2025
Why is my Whirlpool WGT4027HW not cleaning or removing stains?
- M
  Michael SmithAug 31, 2025
  If you're finding that your Whirlpool Washer/Dryer isn't cleaning or removing stains effectively, it could be due to several factors. The washer senses load size and adds the correct amount of water, which is normal and necessary for clothes to move, even if the wash load is below the water line; adding extra water manually results in less effective cleaning. Avoid tightly packing the washer, and load garments in loose heaps evenly around the basket wall, using only dry items. Limit adding garments after the start to one or two items. Add detergent, Oxi products, and color-safe bleach to the bottom of the basket before adding the load items, rather than on top of the load.
T
Terry HessSep 1, 2025
Why are clothes not completely covered with water in my Whirlpool Washer/Dryer?
- K
  kenneth87Sep 1, 2025
  If your clothes are not completely covered with water in your Whirlpool Washer/Dryer, it is because this washer uses much less water than traditional top-load washers.
A
Andrew JimenezSep 4, 2025
What to do if there are residues remaining on my Whirlpool WGT4027HW load after washing?
- C
  Christine VaughanSep 4, 2025
  If you're experiencing residues remaining on the load after washing with your Whirlpool Washer/Dryer, it may be due to sand, pet hair, lint, remaining detergent, bleach, and other residues that require additional rinsing. Select the Heavy Duty cycle to help remove these residues.
M
Michelle HoffmanSep 5, 2025
How to get rid of odors in my Whirlpool WGT4027HW Washer/Dryer?
- O
  Oscar RamosSep 5, 2025
  If you notice odors coming from your Whirlpool Washer/Dryer, it could be due to a lack of monthly maintenance. Please refer to the “Washer Care” section in “Washer/Dryer Maintenance.” Ensure you unload the washer as soon as the cycle is complete and that you are correctly measuring detergent, following the manufacturer’s directions. You can also refer to the “Washer Care” section for more information.
J
James ClementsSep 7, 2025
What causes incorrect dispenser operation in my Whirlpool WGT4027HW Washer/Dryer?
- M
  Mrs. Amber Williams MDSep 7, 2025
  If you're experiencing incorrect dispenser operation with your Whirlpool Washer/Dryer, it could be due to a clogged dispenser. Make sure to use only liquid chlorine bleach in the bleach dispenser and only fabric softener in the fabric softener dispenser.

Whirlpool WGT4027HW Specifications

General

Brand	Whirlpool
Model	WGT4027HW
Appliance Category	Washer/Dryer
Color	White
Energy Star Certified	No
Voltage	120V
Width	27 in.
Control Type	Electronic
Agitator Type	Agitator
Type	Washer/Dryer Combo
Height	44 in
Appliance Type	Top Load Washer/Dryer Combo