Winegard SENSAR - User Manual

1
FIG. 4
Measure from
the recess on
top of handle
to the ceiling.
NOTE: Figure 1 shows the minimum distance the mount can be
located from edge of vehicle roof. Check with your dealer or the
manufacturer for information about options in the roof for mounting
the antenna. A reinforced roof area, or a prewired coax cable, may be
available. For sloped/round roofs, use Winegard Model RW-2000
exterior roof wedge, to level installation. An interior wedge, IW-5000,
is also available.
STEP 2: Using template on page 7, drill 1-3/4" hole through roof and
ceiling of vehicle. Be careful not to damage any wiring between roof and
ceiling.
STEP 3: Drill 1/2" hole for cable entry through roof of vehicle only. DO
NOT DRILL THROUGH CEILING. Route cable through ceiling and wall to
power supply location.
STEP 4: The mount is designed to fit roofs from 1" to 4-3/4" thick. As
supplied, the mount will fit a roof 4-3/4" thick. If roof is less than 4-3/4"
thick, cut elevating shaft and directional handle to size, steps shown in
figures 2, 3, 4 and 5. If roof is more than 4-3/4" thick (max. 7"), a
directional handle extension is needed. Order Winegard Model
EK-1036, Directional Handle Extension.
IMPORTANT: The handle and extension must be glued together after
checking that you have the correct length. The handle will not work
properly if it is not glued together! (PVC glue is recommended; for your
safety, use according to manufacturer's directions.)
NOTE: If using roof wedge RW-2000 or interior wedge IW-5000, put in
place before installing base plate or interior hardware.
STEP 5: Center elevating shaft in hole on roof.
Temporarily secure base plate to roof with two screws
provided. (Do not apply sealant at this time).
Inside unit, make a mark on the shaft 1-1/2” below
ceiling and cut shaft on this mark. See figure 2.
After cutting elevating shaft, push directional handle
up into ceiling over shaft being careful to align keys
inside directional handle onto keyways on bottom of
gear housing. (NOTE: The keys only line up one
way; do not force. TIP: Pointer on directional
handle should point toward back of coach if
properly installed.) Make sure directional handle is
snug against bottom of baseplate. Measure distance
between the bottom of the recess on the handle to
the ceiling. See figure 3. Pull handle back down and
transfer this dimension to the shaft end of the
directional handle. Mark it and cut it off here, fig. 4.
If EK-1036 (directional handle extension) is used,
DO NOT CUT EK-1036 extension. Cut excess
length from directional handle only. The handle
and extension must be glued together after
checking that you have the correct length, fig. 5.
FIG. 2
INSTALLATION/OPERATION MANUAL (All Models)
MADE IN U.S.A. (Sensar
®
III head - U.S. Patent D500,496 )
∗∗
∗∗
∗
FIGURE 1
1-1/2"
FIGURE 3
FIGURE 5
EK-1036
Extension
DO NOT CUT
extension
2-1/4"
•
–
•
–
Cut excess
length from
directional
hande
Measure
from bottom
of recess on
top of handle
2452013-Installation/Operation
10"
10"
3¾"
3¾"
10" Minimum
Distance
®®
Bottom of
Baseplate
Bottom of
Gear
Housing
–
–
*
WINEGARD SENSAR ANTENNAS
STEP 1: Choose location for antenna. Figure 1 illustrates placement of the Sensar, showing it in travel position.
You must be able to raise and rotate antenna without interfering with other roof-mounted equipment. Make sure
inside ceiling area is clear to mount ceiling plate.
Directional Handle
–
–
Shaft
End
*
Transfer the
measurement
from Fig. 3 to
shaft end and
cut off.

Summary

Installation Procedure

Initial Setup and Mounting

Covers choosing location, drilling, adjusting mount, and installing shaft/handle.

Antenna Head and Base Plate Assembly

Attaching antenna head, connecting coax, and mounting base plate.

Ceiling Plate and Handle Assembly

Mounting ceiling plate and assembling directional handle and crank.

Non-Amplified Model Connection

Connecting the downlead cable to the TV set for non-amplified systems.

Amplified Models Setup

Wall Plate and Power Supply Installation

Covers selecting location, wiring, connecting cables, and mounting the power supply.

Power Supply Operation Check

Procedure to verify power supply functionality by checking TV picture degradation.

Optional Amplified Wallplate

Details on adding an optional signal amplifier for improved picture quality.

Operation and Maintenance

Antenna Positioning

Instructions for raising, lowering, and rotating the antenna for optimal reception.

Lubrication Guidelines

Annual and semi-annual lubrication procedures for the elevating gear and shaft.

Operational Safety

Key do's and don'ts for safe and correct operation of the antenna system.

Troubleshooting and Connectivity

F-Connector Installation

Steps for properly installing F-connectors on coaxial cables.

System Performance Diagnostics

Guides to test voltage and diagnose issues with the power supply or cable connections.

Ordering Repair Parts

Available Part Packages

Lists part packages, model numbers, and prices for common replacement components.

Warranty and Service

Limited Warranty Terms and Conditions

Details warranty coverage, proof of purchase requirements, and exclusions.

Product Return and Replacement Procedure

Explains the RMA process and procedure for replacing the elevating shaft assembly.

Winegard SENSAR Specifications

General

Power	12V DC
Impedance	75 Ohms
Frequency Range	UHF 470-862 MHz
Amplification	Built-in amplifier
Compatibility	HDTV signals
Color	White
Material	Plastic