WisyCom MTP61 - FCC and Industry Canada Regulatory Statements; FCC Compliance Rules and Conditions; Industry Canada Compliance and Antenna Use; RF Exposure Limits Evaluation

MTP61 mul-band miniature transmier
16
Statements regarding FCC and Industry Canada
The Wisycom microphone pocket transmier model MTP61 complies with the following requirements: FCC (Federal Communica-
ons Commission) Part 74.
Operaon is subject to the following two condions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operaons.
Changes or modicaon not expressly approved by the party responsible for compliance could void the user’s authority to operate
the equipment.
This device complies with part 15 of the fcc rules.
Operaon is subject to the following two condions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operaon.
Note: the grantee is not responsible for any changes or modicaons not expressly approved by the party responsible for compli-
ance. such modicaons could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the in-
strucons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will not
occur in a parcular installaon. If this equipment does cause harmful interference to radio or television recepon, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separaon between the equipment and receiver.
-Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
EN
This device complies with Industry Canada license-exempt RSS-123 and RSS-210 standard. Operaon is subject to the following two
condions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that
may cause undesired operaon of the device. This radio transmier IC: 11967A-MTP61 has been approved by Industry Canada to
operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna
type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are
strictly prohibited for use with this device.
FR
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence RSS-123 et RSS-
210.
L’exploitaon est autorisée aux deux condions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’ulisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est suscepble d’en compro-
mere le fonconnement.
Le présent émeeur radio IC: 11967A-MTP61 a été approuvé par Industrie Canada pour fonconner avec les types d’antenne é
numérés ci-dessous et ayant un gain admissible maximal et l’impédance requise pour chaque type d’antenne. Les types d’antenne
non inclus dans cee liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l’exploitaon de
l’émeeur.
Antenna types (50 Ohm impedance, max gain 2.1dBi): AWSS-507: band 470-547 MHz, AWSS-590: band 547-663 MHz, AWSS30-
950: band 940-960 MHz.
This equipment complies has been evaluated for and shown compliant with the FCC and ISED RF Exposure limits. The unit of mea-
surement for RF exposure is Specic Absorpon Rate (SAR). The FCC SAR limits for is 1.6W/Kg per 1g of ssue
The maximum SAR levels tested has been shown to be 0.85 W/kg at head with 0mm of separaon distance from the body.
This device operates on a no-interference, no-protecon basis. Should the user seek to obtain protecon from other radio services
operang in the same TV bands, a radio license is required. For further details, consult Innovaon, Science and Economic develop-
ment Canada’s Client Procedures Circular CPC-2-1-28, Voluntary Licensing of License-Exempt Wireless Microphones in TV Bands.
The FCC and IC identifier is visible in the display when the device is switched on and it is also available by accessing the Info>
STD submenus.