What to do if external fault at programmable Input E1 on Wolf CGB-2K-24 Boiler?
If your Wolf Boiler displays 'External fault at programmable Input E1', it means an external fault has been reported at programmable input E1 because the fault message contact at E1 has opened. Rectify the external fault and check the lead. Acknowledge the fault message afterward.
What to do if there is flame failure in Wolf CGB-2K-24 Boiler?
If the Wolf Boiler shows a 'Flame failure' error, it could be due to several reasons. First, verify the gas type setting on both the gas valve and the AM/BM. Then, check the gas supply pressure. Inspect the condition of the ionization electrode, cleaning or replacing it if necessary, and ensure its gap and position are correctly set. Finally, examine the flue path inside and outside the appliance for any leaks or blockages.
How to fix HLSC excess temp on Wolf CGB-2K-24 Boiler?
If your Wolf Boiler displays 'HLSC excess temp,' it indicates that the temperature at the heat exchanger cover has exceeded 185 °C. Check the cables and plugs connected to the high limit safety cut-out (HLSC). If the electrical connections are fine but there's still no function, replace the HLSC. Another possible cause is a contaminated combustion chamber, in which case, clean or replace the combustion chamber.
What to do if TL excess temp on Wolf CGB-2K-24?
If your Wolf Boiler shows a 'TL excess temp' error, it means one of the temperature sensors eHLSC1 or eHLSC2 on the combustion chamber has exceeded the high limit safety cut-out limit (108 °C). Check the system pressure and vent the heating circuit. Inspect the cables and plugs of the temperature limiter (eHLSC), and if they are OK but there's no function, replace the eHLSC. Also, check if the pump is running; if not, check its cables and plugs, and if the electrical connection is OK but it's still not working, replace the pump.
What to do if boiler sensor is faulty in Wolf Boiler?
If your Wolf Boiler displays the message 'Boiler sensor faulty' it could be due to excess temperature in the flow (Boiler sensor > 100 °C). First, check if the pump is running. If it is not, check the cables and plugs and if the electrical connection is OK but there is still no function, replace the pump. Another solution is to increase the minimum pump speed. Also, check the leads and plug-in connections of the boiler sensor, and if they are OK but there is still no function, replace the boiler sensor.
What causes timeout calibration error on Wolf CGB-2K-24?
If your Wolf Boiler displays 'Timeout calibration', it means the heating appliance cannot carry out calibration. Check the flue path inside and outside the appliance for any blockages related to flue gas recirculation. Ensure the fan and its wiring are intact. Ensure adequate heat transfer by opening heating circuits.
What causes GLV actuators error on Wolf Boiler?
If your Wolf Boiler displays 'GLV actuators' there may be several causes. Check the flue path inside and outside the appliance for leaks or blockages related to flue gas recirculation and check for wind effect. Verify the gas type setting on the gas valve and the AM/BM-2. Remove the gas valve retainer and check that the correct gas restrictor is fitted. Check the fan for bearing damage and inspect the cables, plug-in connections, power supply, and switching.
What to do if GCV relay test failed on Wolf CGB-2K-24?
If your Wolf Boiler displays 'GCV relay test', it means the valve test failed and the gas valve is faulty. Replace the gas valve.
Why is fan speed high on Wolf CGB-2K-24 Boiler?
If the Wolf Boiler displays 'Fan speed >', it means the fan does not stop. Check the fan's cables, plug-in connections, power supply, and switching. If the fault occurs repeatedly, replace the fan.
What to do if outside sensor is faulty in Wolf CGB-2K-24?
If your Wolf Boiler displays 'Outside sensor faulty,' it means that the outside sensor or sensor lead has a short circuit or break. For the eBus outside temperature sensor, refer to its instructions. Similarly, for a wireless outside sensor, consult its specific instructions.
Provides immediate actions to take if gas odor is detected.
Warns about the risk of electrocution from live electrical parts.
Advises caution due to hot water and potential scalding.
Warns about hot boiler components causing burns.
Details safety procedures for working on the boiler system.
Specifies minimum clearances required around the boiler for installation.
Emphasizes the need for a licensed fitter for gas connections.
Details electrical connection requirements and safety warnings.
Step-by-step guide for filling the heating system and trap.
Step-by-step instructions for draining the heating system.
Details the procedure for changing the gas type to LPG.
Step-by-step guide for checking gas supply pressure.
States that conversion must be done by authorized contractors.
Lists steps for commissioning and fields for test values.
Describes safety devices related to temperature monitoring.
Explains safety devices for monitoring system pressure.
Details tightness testing for connections to adjacent appliances.
Describes that a parameter reset returns settings to factory defaults.
General guidelines for troubleshooting and safety precautions.
Steps to follow when a fault occurs.
Shows the wiring diagram for the HCM-2 module.
Displays the wiring diagram for the GBC-e module.
General| Type | Condensing Boiler |
|---|---|
| Max. Heat Output (80/60 °C) | 24 kW |
| Efficiency (Hs) | 98% |
| NOx Class | 6 |
| Fuel Type | Natural Gas |
| Operating Pressure | 3 bar |
To Next Page
