What to do if external fault at programmable Input E1 on Wolf CGB-2?
If your Wolf Boiler displays 'External fault at programmable Input E1', it means an external fault has been reported at programmable input E1 because the fault message contact at E1 has opened. Rectify the external fault and check the lead. Acknowledge the fault message afterward.
What to do if there is flame failure in Wolf CGB-2?
If the Wolf Boiler shows a 'Flame failure' error, it could be due to several reasons. First, verify the gas type setting on both the gas valve and the AM/BM. Then, check the gas supply pressure. Inspect the condition of the ionization electrode, cleaning or replacing it if necessary, and ensure its gap and position are correctly set. Finally, examine the flue path inside and outside the appliance for any leaks or blockages.
How to fix HLSC excess temp on Wolf CGB-2?
If your Wolf Boiler displays 'HLSC excess temp,' it indicates that the temperature at the heat exchanger cover has exceeded 185 °C. Check the cables and plugs connected to the high limit safety cut-out (HLSC). If the electrical connections are fine but there's still no function, replace the HLSC. Another possible cause is a contaminated combustion chamber, in which case, clean or replace the combustion chamber.
What to do if TL excess temp on Wolf CGB-2?
If your Wolf Boiler shows a 'TL excess temp' error, it means one of the temperature sensors eHLSC1 or eHLSC2 on the combustion chamber has exceeded the high limit safety cut-out limit (108 °C). Check the system pressure and vent the heating circuit. Inspect the cables and plugs of the temperature limiter (eHLSC), and if they are OK but there's no function, replace the eHLSC. Also, check if the pump is running; if not, check its cables and plugs, and if the electrical connection is OK but it's still not working, replace the pump.
What to do if boiler sensor is faulty in Wolf Boiler?
If your Wolf Boiler displays the message 'Boiler sensor faulty' it could be due to excess temperature in the flow (Boiler sensor > 100 °C). First, check if the pump is running. If it is not, check the cables and plugs and if the electrical connection is OK but there is still no function, replace the pump. Another solution is to increase the minimum pump speed. Also, check the leads and plug-in connections of the boiler sensor, and if they are OK but there is still no function, replace the boiler sensor.
What causes timeout calibration error on Wolf CGB-2 Boiler?
If your Wolf Boiler displays 'Timeout calibration', it means the heating appliance cannot carry out calibration. Check the flue path inside and outside the appliance for any blockages related to flue gas recirculation. Ensure the fan and its wiring are intact. Ensure adequate heat transfer by opening heating circuits.
What causes GLV actuators error on Wolf CGB-2?
If your Wolf Boiler displays 'GLV actuators' there may be several causes. Check the flue path inside and outside the appliance for leaks or blockages related to flue gas recirculation and check for wind effect. Verify the gas type setting on the gas valve and the AM/BM-2. Remove the gas valve retainer and check that the correct gas restrictor is fitted. Check the fan for bearing damage and inspect the cables, plug-in connections, power supply, and switching.
What to do if GCV relay test failed on Wolf Boiler?
If your Wolf Boiler displays 'GCV relay test', it means the valve test failed and the gas valve is faulty. Replace the gas valve.
Why is fan speed high on Wolf CGB-2 Boiler?
If the Wolf Boiler displays 'Fan speed >', it means the fan does not stop. Check the fan's cables, plug-in connections, power supply, and switching. If the fault occurs repeatedly, replace the fan.
What to do if outside sensor is faulty in Wolf CGB-2 Boiler?
If your Wolf Boiler displays 'Outside sensor faulty,' it means that the outside sensor or sensor lead has a short circuit or break. For the eBus outside temperature sensor, refer to its instructions. Similarly, for a wireless outside sensor, consult its specific instructions.
Ensures safekeeping of all instruction manuals and documents.
Provides guidance on boiler operation, maintenance, and safety to the user.
Lists items included with the boiler and necessary accessories for installation.
Covers gas leaks, flue gas, electrical hazards, scalding, and burns.
Safety measures for working on the system and requirements for inspection and service.
Technical drawings showing boiler dimensions and internal component arrangement.
Detailed technical data including output, efficiency, and connections.
Explains gas-adaptive control and the system calibration process.
Instructions for casing removal, minimum clearances, and installation environment.
Covers boiler mounting, and connecting supply lines for different wall types.
Details gas, heating circuit, safety valve, and cold water/DHW connections.
Instructions and considerations for routing air and flue gas systems.
Essential information on electrical connection, safety rules, and control unit overview.
Guidance on connecting power, outputs, inputs, sensors, and accessories.
Procedures for installing, removing, and understanding AM/BM-2 modules.
Explanations of module features, keys, and menu navigation.
Overview of control parameters, system configurations, and modification guidelines.
Explanations of various control parameters (HG01-HG61) and their functions.
Procedures for filling, water treatment, draining the heating system, and trap filling.
A checklist of essential steps to confirm during boiler commissioning.
Process for determining, changing, and configuring the gas type.
Procedure for verifying the gas supply pressure for safe operation.
Method for matching maximum heating output using fan speed settings.
Procedures for checking intake air and flue gas parameters for optimal combustion.
Steps for converting between combi boiler and boiler with cylinder configurations.
Guide on adjusting the flow limiter for the domestic hot water draw-off rate.
Explanation of the modulating heating circuit pump's operating modes and settings.
Description of the various safety sensors and monitoring systems in the boiler.
Technical data, routing options, connection types, and safety for air/flue gas systems.
Steps to reset all parameters to factory default settings.
Schematics illustrating the wiring connections for the control modules.
Basic principles, fault/warning message interpretation, and resolution steps.
Detailed list of fault codes, possible causes, and remedies for appliance issues.
Guide to interpreting warning messages, their causes, and necessary actions.
Regulatory product fiche and technical parameters compliant with EU regulations.
Manufacturer's declaration confirming product compliance with relevant EU directives.
General| Efficiency (GCV) | Up to 98% |
|---|---|
| Efficiency (AFUE) | Up to 95% |
| Type | Condensing Boiler |
| Fuel Type | Natural Gas or Propane |
| Dimensions | Varies by model |
| Weight | Varies by model |
To Next Page
