To Next PageTo Next PageWhy Wood-mizer 1992 LT40HD Saw blade does not track right?
If the Wood-Mizer Saw blade does not track right, readjust on the Drive Wheel if the cant adjustment is incorrect. Replace B-57 belts if the belts are flat or worn.
General| Model | LT40HD |
|---|---|
| Year | 1992 |
| Max Log Diameter | 36 inches |
| Blade Thickness | 0.042 inches |
| Horsepower | 20 HP (Kohler) or 25 HP (Kubota) |
| Blade Length | 144 inches |
| Fuel Capacity | 5 gallons |
Safety precautions for handling bandsaw blades, including personal protective equipment.
Procedures and safety warnings for setting up the sawmill on various terrains for stability.
Critical safety instructions for operating the sawmill and its components during use.
Specifications and part numbers for various belts used on the sawmill.
Recommended blade types and sizes based on wood type and engine size for performance.
Log size capacities and production output for different sawmill models.
Details on available engine and motor options for the sawmills.
Physical dimensions and weight specifications for LT30HD and LT40HD models.
Identification of major sawmill components with a visual diagram for reference.
Diagrams illustrating the hydraulic system for different revisions of the sawmill.
Detailed list of hydraulic components, including part numbers and descriptions.
Specifications for hydraulic hoses, including component codes and lengths.
Steps for setting up a stationary sawmill on firm footing for stability.
Procedures for setting up a portable sawmill, including outrigger adjustment.
Initial steps to prepare the sawmill for operation, specific to TUV trailers.
Step-by-step guide on how to safely replace the bandsaw blade.
Instructions for correctly tensioning the blade using the tension gauge.
Method for aligning the blade on the wheels for optimal cutting performance.
Safety precautions and steps for starting the sawmill's engine or motor.
Operation of hydraulic controls for loading logs, with revisions noted.
Procedures for loading, turning, and securely clamping logs onto the sawmill bed.
Instructions for using and storing the clamp extension for small logs or cants.
How to operate the up/down switch for adjusting cutting head height.
Adjusting the blade guide arm to clear the log during cutting operations.
How to engage and disengage the clutch and brake for blade operation.
Operating the power feed system for carriage movement and speed control.
Step-by-step guide for performing standard cuts on a log.
Procedures for edging boards to create clean, square sides.
Using the sight gauge to determine precise blade height for cuts.
Understanding and using the blade height scales for accurate lumber thickness.
Instructions for using the water lube system to keep the blade clean.
Steps to secure the sawmill for safe transport and towing.
Estimated life expectancy of common replacement parts for planning maintenance.
Maintenance procedures for blade guide rollers, including lubrication and inspection.
Cleaning around velocity fuse valves on the log loader cylinders.
Cleaning sawdust from blade wheel housings and adjusting blade screw.
Cleaning and lubricating track rails, wipers, and scrapers for smooth operation.
Lubrication schedule for greasable track roller bearings.
Cleaning and lubricating vertical mast rails to prevent rust and ensure smooth movement.
Lubrication of drum switch contacts for reliable operation.
General lubrication points for blade guide arms, mechanisms, and chains.
Lubrication of tensioner system components, including chrome rods and screw handle.
Instructions for rotating and checking blade wheel belts for wear.
Procedures for checking and adjusting the brake strap for quick stopping.
Checking hydraulic fluid level, replacing filters, and servicing the drive motor.
Refilling fluid in the drive-side cylinder bearing housing.
Greasing gear reducer shaft bearing and adjusting up/down belt and chain.
Adjusting the power feed belt and chain tension for proper operation.
Checking mill alignment, safety decals, and electrical connections.
Troubleshooting common sawing issues like dull blades, breakage, and tracking.
Diagnosing and resolving electrical issues with motors, switches, and battery.
Troubleshooting issues related to the power feed system's jerky operation or motor overheating.
Using LED lights on the circuit board to diagnose power feed problems.
Troubleshooting common hydraulic system issues, including pump response and leaks.
Steps for aligning engine, motor, and drive pulleys for optimal belt performance.
Procedure to test the variable speed switch for jerky responses.
A test to determine if power feed problems are mechanical or electrical.
A mechanical inspection of the power feed system components.
How to check hydraulic pressure for different sawmill revisions.
Overview of steps required for accurate sawmill alignment.
Steps for properly setting up the sawmill frame for alignment.
Installing a blade and aligning it with the blade wheels.
Adjusting the nylon pads on the saw head for proper vertical mast contact.
Adjusting lower track rollers for square cuts and accurate board dimensions.
Aligning the main bed rails parallel to the blade for precision cuts.
Adjusting the vertical position of the blade guide arm for blade support.
Adjusting the horizontal position of the blade guide arm for proper blade clearance.
Steps for aligning the inner and outer blade guide assemblies.
Adjusting blade guides to achieve proper blade deflection during cuts.
Adjusting the vertical tilt of the blade guide to prevent blade tilting.
Setting the correct spacing for blade guide flanges relative to the blade.
Adjusting the horizontal tilt of the blade guide rollers.
Horizontally adjusting side supports to ensure square cuts.
Vertically adjusting side supports to be square to the bed rails.
Adjusting the clamp stop to align with the side supports.
Adjusting pivot bed rails to be level with main bed rails for cutting long cants.
Adjusting the sight gauge to accurately indicate blade position over bed rails.
Compensating for saw head drop on wide logs by adjusting track rollers.
Calibrating the blade height scale to accurately reflect blade-to-bed distance.
