To Next PageTo Next PageWhat to do if drive belts come off pulleys when disengaging blade on Wood-mizer Saw?
If the drive belts come off the pulleys when disengaging the blade on your Wood-mizer Saw, adjust the brake strap if it is too loose. Realign the brake drum on the drive shaft if it is misaligned. Also, adjust the brake strap if it's tightened unevenly.
What to do if up/down or power feed motors do not work on Wood-mizer LT30HD?
If the up/down or power feed motors on your Wood-Mizer Saw do not work, replace the drum switch or remove the control panel cover and clean the contacts if the contacts in the drum switch are worn. Replace the motor if it is burned out. Check for loose wire or terminal connections on the battery.
What causes the lumber from Wood-mizer LT30HD Saw to not be square?
If the lumber from your Wood-mizer Saw is not square, adjust the side supports to be square to the bed. Ensure the blade is parallel to the bed rails, remove any sawdust or bark between the cant and bed rails, and resharpen and reset the blade to address tooth set problems.
What causes the Wood-mizer LT30HD battery to not stay charged?
If the Wood-Mizer Saw battery will not stay charged, ensure the key switch is OFF when not in use. Check for shorts in the system and have the charging system checked by an authorized Onan dealer. Also, check fluid levels in the cells and add proper solution, adjust the low end RPM, and check for loose wires on the alternator light, replacing it if necessary.
Why do Wood-mizer LT30HD blades break prematurely?
If Wood-mizer Saw blades break prematurely, replace worn blade wheel belts (B-57) if they are contacting the metal pulley. Ensure proper sharpening techniques are used (refer to the Sharpener Manual). Also, ensure the blade tension is set to the recommended specifications.
What to do if Wood-mizer Saw makes wavy cuts?
If your Wood-mizer Saw is making wavy cuts, try slowing the feed rate. Resharpen the blade, ensuring you consult the Sharpener Manual. Adjust the blade guides, use water lube to address sap buildup, and resharpen and reset the blade to correct tooth set issues.
How to prevent Wood-mizer Saw blades from dulling quickly?
To prevent Wood-mizer Saw blades from dulling quickly, ensure you clean or debark logs, especially on the entry side of the cut. If grinding teeth, grind just enough metal to restore sharpness and use water/coolant. Also, ensure proper sharpening techniques are used.
Why do drive belts wear prematurely on Wood-mizer LT30HD?
If the drive belts on your Wood-mizer Saw wear prematurely, align the pulleys if the engine/motor and drive pulleys are out of alignment. See Section 4.6 for instructions.
What to do if blade does not track right on Wood-mizer Saw?
If the blade on your Wood-mizer Saw does not track right, readjust on the Drive Wheel if the cant adjustment is incorrect. Replace B-57 belts if flat or worn belts are the cause.
General| Max Log Diameter | 30 inches |
|---|---|
| Blade Thickness | 0.042 inches |
| Hydraulic System | Optional |
| Max Width of Cut | 28 inches |
| Blade Width | 1.25 inches |
| Power Options | Gas, Electric |
| Engine Power | 27 HP |
| Track Length | 17 feet |
| Track Width | 4 inches |
| Blade Length | 158" (4013 mm) |
Detailed technical specifications for the sawmill models.
Essential safety guidelines and warnings for operating the sawmill.
Procedures for preparing and setting up a stationary sawmill.
Procedures for preparing and setting up a portable sawmill.
Step-by-step guide for loading, turning, and clamping logs onto the sawmill bed.
Detailed instructions on the process of cutting logs using the sawmill.
Procedures for inspecting, adjusting, and maintaining blade guides.
Instructions for lubricating and maintaining the blade tensioner system.
Guidelines for checking hydraulic fluid levels and replacing filters.
Common sawing issues, their causes, and solutions.
Troubleshooting steps for electrical issues affecting the sawmill's operation.
Steps for performing routine alignment to ensure accurate sawing.
Detailed procedures for a comprehensive sawmill alignment.
Diagram illustrating the sawmill's hydraulic system layout and components.
