Wood-mizer LT30HD - User Manual

Other manuals for Wood-mizer LT30HD

Manual13 pages

Safety, Operation, Maintenance & Parts Manual45 pages

Questions and Answers

A
Ashley DawsonSep 23, 2025
Why pump motor runs with no response from cylinders on Wood-mizer LT30HD Saw?
- J
  Julie VasquezSep 23, 2025
  If the pump motor runs with little or no response from the cylinders on your Wood-Mizer Saw, test the battery and replace or recharge as necessary if the battery is low or dead. Remove the motor from the pump and inspect it, repairing or replacing as necessary if the pump motor is defective. Check the ground connection between the pump and saw frame if there is a poor ground connection.
J
Jennifer McfarlandAug 23, 2025
What to do if blade does not track right on Wood-mizer Saw?
- M
  Michael VangAug 25, 2025
  If the blade on your Wood-mizer Saw does not track right, readjust on the Drive Wheel if the cant adjustment is incorrect. Replace B-57 belts if flat or worn belts are the cause.
J
John LambAug 25, 2025
Why do drive belts wear prematurely on Wood-mizer LT30HD?
- R
  Robert Anderson MDAug 26, 2025
  If the drive belts on your Wood-mizer Saw wear prematurely, align the pulleys if the engine/motor and drive pulleys are out of alignment. See Section 4.6 for instructions.
D
Douglas JohnsonAug 27, 2025
How to prevent Wood-mizer Saw blades from dulling quickly?
- J
  John NicholsAug 27, 2025
  To prevent Wood-mizer Saw blades from dulling quickly, ensure you clean or debark logs, especially on the entry side of the cut. If grinding teeth, grind just enough metal to restore sharpness and use water/coolant. Also, ensure proper sharpening techniques are used.
M
maria78Aug 27, 2025
What to do if Wood-mizer Saw makes wavy cuts?
- P
  Phillip Taylor MDAug 27, 2025
  If your Wood-mizer Saw is making wavy cuts, try slowing the feed rate. Resharpen the blade, ensuring you consult the Sharpener Manual. Adjust the blade guides, use water lube to address sap buildup, and resharpen and reset the blade to correct tooth set issues.
T
Thomas LarsonSep 15, 2025
How to fix fluid leak around pump box of Wood-mizer LT30HD?
- D
  david18Sep 15, 2025
  To address a fluid leak around the pump box of your Wood-Mizer Saw, thoroughly wipe the pump to locate the source of the leak. You may need to unbolt the pump to clean behind it.
V
Victoria ManningSep 13, 2025
What to do if blade does not stop immediately after disengaging on Wood-mizer LT30HD Saw?
- K
  Kaitlin WatsonSep 13, 2025
  If the blade on your Wood-mizer Saw does not stop immediately after disengaging, adjust the brake strap.
M
Michelle JonesSep 14, 2025
Why does Wood-Mizer Saw cut out and then work again?
- L
  Lisa BrownSep 14, 2025
  If everything works and then cuts out and works again on your Wood-Mizer Saw, check the connection in the battery.
S
stacey61Sep 5, 2025
Why does height adjustment jump on Wood-mizer LT30HD?
- W
  wileylaurenSep 5, 2025
  If the height adjustment on your Wood-mizer Saw jumps or stutters, lubricate the mast track surface. Adjust the up/down chain, adjust the vertical wear pads if they are too tight and adjust belts if drive belt(s) loose.
K
Kenneth JeffersonSep 2, 2025
Why are boards thick or thin on ends or middle when using Wood-mizer LT30HD?
- A
  Ashley SandovalSep 2, 2025
  If boards cut by your Wood-mizer Saw are thick or thin on the ends or middle, take equal cuts off opposing sides after the log has been squared. Remove a board, repeat, keeping the heart in the middle of the cant, making it your last cut. Resharpen and reset the blade if there's a set in the teeth. Realign the sawmill if the bed rails are misaligned.

Wood-mizer LT30HD Specifications

General

Max Log Diameter	30 inches
Blade Thickness	0.042 inches
Hydraulic System	Optional
Max Width of Cut	28 inches
Blade Width	1.25 inches
Power Options	Gas, Electric
Engine Power	27 HP
Track Length	17 feet
Track Width	4 inches
Blade Length	158" (4013 mm)