Why is my Woodbridge Toilet not flushing?
If your Woodbridge Toilet isn't flushing, the issue might be due to a few reasons. Check if the water supply hose is buckled, causing a blockage; if so, solve the buckling. Also, ensure the fill valve is turned on and that the water supply isn't cut off. If it is, connect the water supply and wait for the water to fill.
Why is my Woodbridge Toilet flushing poorly?
A poor flush in your Woodbridge Toilet could stem from a few causes: A partially blocked water supply hose due to buckling – solve the buckling to restore full flow. The fill valve may not be fully open, so ensure you turn it on completely. Lastly, a dirty filter can cause a blockage; try cleaning the filter.
How to flush Woodbridge B0960S Toilets during a power outage?
In case of a power failure with your Woodbridge toilet, you can manually flush by pressing the full/half flush button.
What to do if spray wand cannot retracted in Woodbridge Toilets?
If the spray wand on your Woodbridge Toilet won't retract, first, check if the power is off. If it is, gently push back the wand and wait for the power to return. Alternatively, the wand might be stuck due to impurities; clear away any obstructions.
What to do if spray wand cannot stretch out in Woodbridge Toilets?
If the spray wand on your Woodbridge Toilet isn't stretching out, make sure the power is on. If it was off, gently push back the wand and wait for the power to come back on. Also, ensure you are properly seated in the sensing area; the wand won't extend if it doesn't detect your presence.
Why is the deodorization malfunctioning on my Woodbridge Toilet?
The deodorization function on your Woodbridge Toilet might not work if you aren't properly seated in the sensing area; adjust your position to ensure you're detected. Also, it's normal for the deodorization function to continue working after you leave the seat to ensure complete odor elimination.
Why is the seat temperature not hot on my Woodbridge Toilet?
If the seat temperature on your Woodbridge Toilet isn't hot enough, check if the seat temperature is set to a normal level and reset it to your desired warmth. Also, if the toilet is in standby mode, shift to function mode for at least 3 minutes to activate the heating.
How to fix controller display on Woodbridge B0960S?
If the controller on your Woodbridge Toilet isn't displaying anything, the battery polarity might be reversed. Try reloading the battery correctly.
Why is the water not hot in my Woodbridge Toilet?
If the water in your Woodbridge Toilet isn't hot, it might be because the water temperature is set to a normal level. Try resetting the water temperature to your desired setting.
Why is the wind temperature not hot on my Woodbridge Toilet?
If the wind temperature on your Woodbridge Toilet isn't hot enough, the wind temperature might be set to a normal level. Try resetting the wind temperature to your preferred warmth.
Emphasizes the importance of reading all safety instructions before operation.
Instructions for installing the water supply angle valve.
Steps for using cardboard templates during toilet installation.
Procedure for placing and securing the ceramic toilet.
Instructions for opening the water supply valve.
Guidance on connecting and turning on the electrical power.
Procedure for the product to perform an initial self-check.
How to clean and maintain the main body of the toilet.
Procedures for cleaning and maintaining the spray nozzle.
Procedures for handling power or water interruptions.
Alternative control method using the toilet's built-in panel.
Instructions for replacing the batteries in the remote control.
Steps to remove water from the unit for storage or winterization.
Description of the power button and its functions.
Explanation of the flush button's operation.
Details on the drying function.
Information on the front cleaning function.
Information on the rear cleaning function.
Steps for mounting the remote control holder.
How to set up the automatic rear cleaning cycle.
How to set up the automatic front cleaning cycle.
How to set up combined automatic rear and front cleaning.
Procedure for configuring the energy saver operational hours.
Using a quick press to activate nozzle self-cleaning.
Using a long press to activate nozzle self-cleaning for a longer duration.
Setting up the automatic open/close feature for the lid and seat.
How to turn the night light feature on or off.
General| Toilet Type | One-Piece |
|---|---|
| Water Consumption | 1.28 GPF |
| Material | Vitreous China |
| Color | White |
| Bowl Shape | Elongated |
| Rough-in | 12 inches |
| Seat Included | Yes |
| Seat Material | Plastic |
| ADA Compliant | Yes |
| Flush Technology | Siphonic |
To Next Page