Why am I seeing streaking conditions in the swath of my Woods Lawn Mower?
Streaking in the swath can occur for several reasons. First, the grass may be too wet, so allow it to dry before mowing. Second, the blades may not be cutting grass pressed down by the tractor tires; try slowing the tractor's ground speed while maintaining full PTO rpm, and cutting lower can also help. Finally, dull blades can cause streaking, so sharpen or replace them.
What to do if the Woods Lawn Mower discharges material unevenly, leaving bunches along the swath?
Uneven discharge and bunching can happen for several reasons. It could be that the material is too high and there's too much of it. Try reducing ground speed while keeping the tractor PTO at 540 RPM, or make two passes, raising the cutter for the first pass and lowering it for the second, cutting at a 90° angle to the first pass. Ensure the rear of the cutter is high enough to discharge material without causing other issues. Also, wet grass can cause this issue, so allow the grass to dry or slow down the tractor while maintaining full PTO rpm, and cutting lower. Lastly, the rear of the cutter might be too low, trapping material. Adjust the cutter height and attitude to resolve this.
How to fix Woods Lawn Mower cutting grass lower in the center of the swath than at the edge?
If the grass is being cut lower in the center of the swath compared to the edge, the height of the cutter might be lower at the rear or front. To fix this, adjust the cutter height and attitude, ensuring the rear and front are within 1/2" of the same height.
What to do if my Woods Lawn Mower cutter won't cut all the time (Slip clutch drive only)?
The slip clutch may be slipping. Adjust the slip clutch according to instructions.
Why does my Woods Cutter leave streaks in the swath?
Streaking in the swath when using your Woods Cutter can occur for several reasons. First, the conditions might be too wet for mowing; allow the grass to dry before mowing. Second, the blades might be unable to cut the grass pressed down by the tractor tires; try slowing down the tractor's ground speed while keeping the engine running at full PTO rpm. Lastly, dull blades can also cause streaking; sharpen or replace the blades.
What to do if the Woods Cutter discharges material unevenly?
Uneven discharge of material from the Woods Cutter, resulting in bunches along the swath, can be due to several factors. If the material is too high or there is too much of it, reduce ground speed while maintaining 540 RPM at the tractor PTO, or make two passes over the material. Wet grass can also cause this issue, so allow the grass to dry before mowing. Additionally, if the rear of the cutter is too low, it can trap material underneath; adjust the cutter height and attitude accordingly.
How to adjust Woods Cutter if grass is cut lower in the center?
If the Woods Cutter cuts the grass lower in the center of the swath compared to the edge, it may be because the cutter's height is lower at the rear or front. To fix this, adjust the cutter height and attitude so that the cutter's rear and front are within 1/2" of the same height.
Provides general operational context and warnings about illustrations.
Covers operator training, pre-operation checks, safe operating, and maintenance practices.
Explains decal locations, cleaning, and replacement procedures.
Ensures tractor stability and provides cutter attachment instructions.
Covers driveline attachment, interference checks, and shortening.
Steps for removing, installing, and sharpening cutter blades.
How to adjust the slip clutch for equipment protection.
Common mowing problems and their solutions.
Procedures for gearbox repair and seal replacement for BB48-72 models.
Procedures for repairing the BB84.40 spindle gearbox and seals.
Step-by-step guide for assembling the cutter and installing the driveline.
Instructions for installing protective shields and guards.
Checklists for dealers ensuring proper setup and customer delivery.
Exploded view and parts list for the main frame.
Exploded view and parts list for the hitch assembly.
Torque specifications for SAE and metric bolts.
Guides for bolt sizes, thread types, and manual abbreviations.
General| Cutting Width | 72 inches |
|---|---|
| Weight | 791 lb (359 kg) |
| Tractor HP Range | 30-60 HP |
| Blade Material | Steel |
| Handle Material | Steel |
To Next Page