Woods MRD9 - English

4 5
Thank you
Thank you for choosing a Wood’s
dehumidier. You are one of more
than 300.000 people who have cho-
sen a Wood’s dehumidier to prevent
damages from excessive moisture
and mould. Originating in Canada
in 1950, Wood’s has more than 60
years experience of developing and
manufacturing dehumidiers. When
choosing a Wood’s dehumidier
you’ll get a unit with great quality,
high capacity and that will extract the
most litres per consumed kWh.
Workings of your
dehumidier
The Wood’s MRD9 is a compressor
dehumidier. As the air is drawn
through the dehumidier by the fan,
the air passes over the compressor
cooled copper coils. The coils cool
down the water vapour, separating
the water from the air.
The water drips down from the coils
and is drained away with the water
hose. Left is the dry air that is exhau-
sted in the room. As the dehumidier
condensates the water vapour, heat
energy is released. That is why a
compressor dehumidier will exhaust
warm, dry air that is extra benecial
for drying clothes, laundry, wood etc.
A compressor dehumidier is the
most energy efcient way to remove
excess moist and bad odour. Keep
the relative humidity level between
50% and 60% to maintain a safe and
healthy indoor environment.
1. Security warnings
Please read the security warning
carefully before installing and using
the appliance. If the security regula-
tions are not followed, it may void the
product warranty and even present a
re hazard:
• Unplug the unit from its power
supply before cleaning, storage or
maintenance of its lter.
• This appliance is not intended for
use by persons (including children)
with reduced physical, sensory
or mental capabilities, or lack of
experience and knowledge, unless
they have been given supervision
or instruction concerning use of the
appliance by a person responsible
for their safety.
• The appliance shall be installed
in accordance with national wiring
regulations.
• If the supply cord is damaged,
it must be replaced by the ma-
nufacturer, its service agent or
similarly qualied persons in order
to avoid a hazard.
• Always keep a safe distance from
water sources.
• The appliance is a heat source. It
is very important that the applian-
ce isn’t covered and that it is kept
away from inammable materials
and other heat sources.
• Do not put ngers or other
objects into air inlet or air outlet.
• Do not stand on the machine.
• Do not cover the appliance.
• Do not to alter or reconstruct the
appliance or its power cable in any
way.
• Always drain the water
according to the instructions.
• The compressor in the unit is lled
with a freon free refrigerant. If there
is a leakage on the refrigerant
system you should stop using the
appliance and contact your retailer.
• Do not use the appliance without its
air lter.
2. Installation and
placement
Wood’s dehumidiers are easy to
move around, but bare in mind the
following.
• The dehumidier should not be
placed near radiators or other
heat sources or exposed to direct
sunlight, as it will reduce its perfor-
mance.
• Keep at least 25cm distance from
walls and other obstructions to
maximize the air ow.
• For optimum performance, place
the dehumidier in the middle of
the room.
• Make sure that the air ow from the
inlet and outlet isn’t blocked
Installation:
1. Place the dehumidier on a at
and solid ground, preferably in the
middle of the room.
2. Close all windows and ventilators
in the room. Otherwise, moist air
from the outside will continue to ow
into the room.
3. Connect the dehumidier to a
grounded power outlet.
3. Using the MRD9
Starting and stop the dehumidier
by pressing the ON/OFF button.
The MRD9 will continue to run until
you manually switch it off using the
ON/OFF button.
Automatic defrost
The unit will defrost automatically
when needed and resume to work
when the defrost is completed.
When defrosting, the compressor
and fan shuts off.
English