Woods RT72.40E - Page 33

33 Parts
MAN1249 (2/28/2018)
RT/RTR60.40E & RT/RTR72.40E ROTARY TILLER ASSEMBLY
RT/RTR60.40E RT/RTR72.40E
REF PART PART QTY DESCRIPTION
12 1043919 1043919 1 Link, tailgate mount
13 104390860 104390872 1 Shield, hex shaft
14 1043910 1043910 1 Parking stand
15 1034983 1034983 1 Snap ring, external, 40 mm
16 1031925 (28) 1031925 (36) 1/2 NC x 1-1/4 HHCS, GR8 w/shank
17 33661 33661 2 Category 1 mounting pin, w/nut & lock washer
17A 30007 30007 2 Nut, hex 7/8 NF
17B 30008 30008 2 Washer, lock 7/8
18 1002048 1002048 1 Clutch shield
19 1042365 1042365 1 Drive assembly, complete (See page 33)
20 104391560 104391572 1 Rotor shaft
21 1043917 1043917 1 End plate
22 1043920 1043920 1 Gearbox mount
23 1043918 1043918 1 Bearing cover
24 3231 3231
* 1 3/8 NC x 2 HHCS, GR5
25 14350 14350 * 2 3/8 NC Flange lock nut
26 73163 73163 * 2 5/16 NC Flange whiz nut
27 839 839 * 1 3/8 NC x 1 HHCS, GR5
28 H019 H019 1 Lock pin, 3/8 x 2-1/4
29 104235060 104235072 1 Shield, rubber
30 104391360 104391372 1 Clamp, rubber shield, right
31 1043912 1043912 1 Clamp, rubber shield, center
32 104391460 104391472 1 Clamp, rubber shield, left
33 1043088 1043088 2 Gasket
35 1042303 1042303 1 Seal, 40 x 70 x 10
36 1042352 1042352 1 Bearing asy, 6208 w/seal
37 1031226 (28) 1031226 (36) 1/2 NC flange spiralock
38 39254 39254 4 M8-1.25P x 14 mm HHCS, CL8.8
39 35155 35155
* 4 5/16 SAE Flat washer
40 2472 2472 * 4 5/16 Lock washer
41 44638 44638 1 Chain, 1/4 proof coil, 16 link
42 14139 14139
* 8 5/16 NC Flange lock nut
44 1972 1972 * 1 1/4-28 Tapered thread grease fitting
45 3379 3379 * 10 1/2 NC x 1-1/2 HHCS, GR5
46 6100 6100 * 6 1/2 NC x 1-1/4 HHCS, GR5
47 25475 25475 * 10 1/2 NC x 1 HHCS, GR5, Full thread
48 11900 11900 * 22 1/2 NC Flange lock nut
49 16148 16148 * 2 5/16 NC x 3/4 Carriage bolt, GR5
50 57816 57816 4 1/2 SAE Flat washer, hardened
51 24576 24576 * 2 1/2 NC x 1-3/4 HHCS, GR5
52 51243 51243 * 12 5/16 NC x 1 Carriage bolt, GR5
53 1034984 1034984 1 Snap ring, internal, 80 mm
54 20891 20891 1 Ball bearing, 6208
55 15007 15007
* 1 3/4 NC x 3-1/2 HHCS, GR5
56 1002018 1002018 1 Sleeve, .81 x 1.25 x 2.12
57 2371 2371 * 1 3/4 NC Hex lock nut
58 1043922 1043922 1 RT Tiller model decal set (Not Shown)
59 1043923 1043923 1 RT Reverse Tiller model decal set (Not Shown)
60 1031976 1031976 1 RT Tiller safety decal set (Not Shown)
HHCS Hex Head Cap Screw
* Standard Hardware, Obtain Locally