Why does my Worx Lawn Mower Landroid vibrate?
If your Worx Landroid vibrates, the blade disc may be unbalanced, or the blades may be damaged. Check the blades and replace them if damaged. Remove any debris or foreign objects from the blades and blade disc.
Why does Worx WR167E run outside the boundary wire?
If your Worx Landroid runs outside the boundary wire, doesn't mow within a zone, or moves erratically near it, it could be due to: * The boundary wire of another Landroid or robotic mower being too close. Ensure at least 1m clearance between your boundary wire and any others. * Signal leakage in wet conditions where the wire has been joined or repaired incorrectly. Check boundary wire joints and insulate them for a waterproof connection. * Boundary wire electric signal leakage due to broken insulation. Repair damaged wire with the supplied connectors.
Why is the Worx Lawn Mower charging time so long?
If your Worx Lawn Mower takes much longer to charge than normal, it could be due to: * A poor connection caused by debris on the charging strip. Clean the contact pins on the charging pile and the charging strip on Landroid with a cloth. * The charging protection program being activated due to high temperature. Place the charging station in a shady area or wait until the temperature cools down.
Why does my Worx WR167E Lawn Mower Landroid stop in the working area?
Your Worx Landroid stopping in the working area can be caused by: * An obstacle in the working area. Remove any obstacles. * The cutting height being set too low for the grass length or the grass being too dense. Raise the cutting height gradually. * The extended boundary wire exceeding 300m, which may cause signal problems. Reduce the length of the boundary wire. * The distance between the center of the lawn and the boundary wire exceeding 25m, potentially causing signal attenuation. Reduce this distance to within 25m.
What to do if my Worx WR167E charging time is too long?
If your Worx Lawn Mower takes longer to charge than expected, it could be due to debris on the charging strip causing a poor connection, or the charging protection program may be activated because of high temperature. Clean the contact pins on the charging pile and the charging strip on the Landroid with a cloth. Alternatively, place the charging station in a shady area or wait for the temperature to cool down.
Why Worx Lawn Mower turns on, but the blade disc does not spin?
It's normal for the Worx Landroid blade disc not to spin if it's on but searching for the charging station to recharge.
How to fix LED light not turning on Worx WR167E charging pile?
If the LED light on the Worx Lawn Mower charging pile isn't on, check that the charging station is properly connected to the charger, and that the charger is connected to a suitable power supply.
What to do if Worx Lawn Mower says outside working area?
If your Worx Landroid displays 'Outside working area!' even when inside the boundary, the boundary wire ends may be clamped incorrectly. Try reversing the boundary wire ends and reconnecting them to the charging station.
What to do if Worx WR167E Lawn Mower vibrates?
If your Worx Lawn Mower is vibrating, the blade disc might be unbalanced, or the blades could be damaged. Inspect the blades, replacing any that are damaged. Also, remove any debris or foreign objects from the blades and blade disc.
Why is there a red light on my Worx WR167E charging pile?
A red light on the Worx Lawn Mower charging pile indicates that the boundary wire isn’t connected. Verify the boundary wire is correctly connected to the charging station and inspect the wire for any breaks.
Guidelines for safe use and handling of the lawnmower.
Steps before operating, including installation and area inspection.
General rules for operating the lawnmower safely.
Rules for unattended operation when pets or children are present.
General checks, part inspection, and servicing for Landroid.
Guidelines for safely moving the lawnmower.
Guidelines for maintaining safe distance for RF exposure compliance.
Crucial safety precautions for handling and using the battery pack.
Safety warnings and essential information for operating the Landroid.
Guidelines for environmentally sound disposal of battery packs.
List of all parts included in the packaging.
Visual guide identifying key components and features of the Landroid.
Detailed technical specifications for various Landroid models.
Information on sound levels and necessary hearing protection.
List of recommended accessories and defines the product's intended use.
Advice on blade maintenance for optimal cutting performance.
Step-by-step guide for safely replacing the cutting blades.
Detailed instructions for cleaning different parts of the Landroid.
Guidance on battery charging and winter hibernation storage.
Checks to perform before restarting Landroid for the new season.
Instructions for updating Landroid software via OTA or USB.
Explains Landroid's operational messages and corresponding actions.
Lists common errors, their causes, and solutions.
Identifies common symptoms, causes, and solutions for Landroid problems.
Addresses more complex issues like connectivity and environmental factors.
Guidelines for responsible disposal of electronic waste.
States compliance with relevant directives and standards.
General| Power Source | Battery |
|---|---|
| Battery Voltage | 20V |
| Battery Capacity | 2.0 Ah |
| Cutting Height | 30-60 mm |
| Voltage | 20V |
| Grass Collector Capacity | Not applicable |
To Next Page