To Next Page
H
haysstephanieSep 10, 2025
Why does my Worx Landroid Lawn Mower flip over?
- JJason GreenSep 10, 2025
If your Worx Landroid lawn mower flips over, it may be due to an inclined obstacle on the lawn. Remove the obstacle from the mower’s working area.
Why does my Worx Landroid Lawn Mower flip over?
If your Worx Landroid lawn mower flips over, it may be due to an inclined obstacle on the lawn. Remove the obstacle from the mower’s working area.
Why is my Worx Landroid Lawn Mower cutting grass unevenly?
If your Worx Landroid lawn mower is cutting grass unevenly, several factors could be at play. First, ensure the mowing schedule allots enough hours daily for effective cutting. If the mowing area is too large for your Landroid model, consider reducing the area or increasing the working time. Check the blades; dull blades should be replaced along with their screws to maintain balance. Adjust the cutting height if it's too low for the grass length, raising it gradually. Also, inspect the blade disc for obstructions like grass or debris, and clear any buildup in the blade disc or motor frame box, ensuring the blade disc rotates freely.
Why Worx Landroid Lawn Mower run-times are getting shorter?
If your Worx Landroid lawn mower is experiencing shorter run times between charges, there might be a few reasons. Start by inspecting the blade disc for clogs that could be causing friction and increasing power consumption. Clean the blade disc thoroughly. Also, check for an unbalanced blade disc, and replace the blades if needed. If these steps don't resolve the issue, the battery may be nearing the end of its life and need replacement, or the working time needs to be reset.
Why do Worx Landroid Lawn Mower wheels skid?
If your Worx Landroid lawn mower wheels skid or slip, check for foreign objects like twigs or branches lodged underneath the unit and remove them. Additionally, if the lawn is too wet, wait until it dries before operating the mower.
What to do if my Worx Landroid Lawn Mower displays ‘– E1 –’ error?
If your Worx Landroid lawn mower is displaying ‘– E1 –’ within its working area, and the boundary wire is connected, the boundary wire ends may be clamped incorrectly. Try reversing the boundary wire ends and reconnecting them to the charging station.
How to set the correct time on Worx Landroid Lawn Mower?
If your Worx Landroid lawn mower is not operating at the correct time, ensure the clock is set accurately. Also, verify that the programmed cutting times are correctly set. If you are using the app, check the percentage of weekly operating time set through the app, and correct it if necessary.
What does red light on Worx Landroid Lawn Mower charging base mean?
If the red light is showing on the charging base of your Worx Landroid lawn mower, it indicates that the boundary wire isn’t connected. Check that the boundary wire has been connected correctly to the charging base and ensure there are no breaks in the boundary wire.
Why Worx Landroid Lawn Mower turns on, but the blade disc does not spin?
If your Worx Landroid lawn mower is turning on but the blade disc isn't spinning, it's likely because the Landroid is in the process of searching for the charging base. This is normal behavior; the blade disc remains stationary while it automatically seeks the charging base.
Why does Worx Landroid Lawn Mower slip down a hill?
If your Worx Landroid lawn mower slips out of its working area while going down a hill, it may be due to low grip on the drive wheels. Ensure the wheels are clean and free of mud to maximize grip.
Why does my Worx Landroid Lawn Mower vibrate?
If your Worx Landroid lawn mower vibrates, the blade disc may be unbalanced, or the blades may be damaged. Inspect the blades, replace them if necessary, and remove any debris or foreign objects from the blades and blade disc.
Detailed safety warnings and instructions for proper and safe operation of the machine.
Key warnings for safe operation, keeping distance, and environmental disposal advice.
Lists and illustrates all the components included in the product packaging.
Identifies and labels key parts of the Landroid, such as sensors, ports, and controls.
Instructions on maintaining the sharpness of cutting blades and replacing them.
Guidelines for regularly cleaning the Landroid's upper body, bottom, wheels, and charging contacts.
Advice on proper battery charging, storage, and manual charging procedures.
Recommendations for preparing and storing the Landroid during the winter season.
Instructions for updating the Landroid's software wirelessly via Wi-Fi.
Steps to check the current software version installed on the Landroid.
Guide on how to update the Landroid's software manually using a USB stick.
Details the causes and recommended actions for various error messages displayed by the Landroid.
Provides solutions for common symptoms, such as no power, unbalancing, or uneven cutting.
General| Battery Voltage | 20 V |
|---|---|
| Battery Capacity | 2.0 Ah |
| Maximum Lawn Size | 500 m² |
| Cutting Height Range | 30-60 mm |
| Power Source | Battery |
| Cutting Height Adjustment | Central |
| Maximum Incline | 35% |
| Mowing Area | 500 m² |
