Xantrex XPower 1000 - User Manual

Questions and Answers

B
Brian PerezAug 17, 2025
What to do if the Fault Light is on and there is no output voltage on my Xantrex XPower 1000 Inverter?
- M
  Michael OlsonAug 17, 2025
  If the Fault Light is on and there's no output voltage on your Xantrex Inverter, possible causes include low or high input voltage, thermal shutdown, unit overload, or a short circuit in the output. To resolve this, recharge the battery and check all connections and cables, ensuring the inverter is connected to a 12V battery. Also, verify the charging system's voltage regulation. If it overheated, allow the unit to cool down, reduce the load, and improve ventilation by ensuring the inverter's openings aren't blocked and lowering the ambient temperature. Finally, reduce the load to not exceed the inverter’s output rating and remove any short circuits.
J
Jessica DanielsAug 20, 2025
What to do if there is no output voltage and both the Power Light and Fault Light are off on my Xantrex XPower 1000 Inverter?
- J
  John DavisAug 20, 2025
  If there is no output voltage and both the Power Light and Fault Light are off on your Xantrex Inverter, first, ensure the inverter is turned on and check the wiring to both the inverter and the battery selector switch (if one is installed). If these steps don't resolve the issue, the inverter may be damaged, possibly due to reverse DC input polarity.
N
Nicole FreemanAug 23, 2025
What to do if the fault light is on on my Xantrex XPower 1000?
- C
  Christina Johnson DDSAug 23, 2025
  If the Xantrex Inverter's fault light is on, it could be due to several reasons: * Low input voltage: Recharge the battery and check the connections and cable, ensuring the XPower 1000 is connected to a 12V battery. Also, check the voltage regulation of the charging system. * High input voltage: Check the voltage regulation of the charging system. * Thermal shutdown: Allow the unit to cool off, reduce the load, improve ventilation by ensuring the inverter’s ventilation openings are not obstructed, and reduce the ambient temperature. * Unit overload: Reduce the load, making sure it does not exceed the XPower 1000’s output rating. * Output short circuit: Remove the short circuit.
S
Stacy AustinAug 26, 2025
Why is the output voltage low (96 VAC – 104 VAC) on my Xantrex Inverter?
- J
  John AvilaAug 26, 2025
  A low output voltage (96 VAC–104 VAC) from your Xantrex Inverter may occur if you're using a voltmeter that can't accurately read the RMS voltage of a modified sine wave, or due to low input voltage combined with a load near the maximum allowable power. Use a true RMS reading voltmeter to check the voltage. Also, check the connections and cable to ensure the battery is fully charged. Recharge the battery if needed and reduce the load.
C
cmillsAug 28, 2025
Why is the output voltage low on my Xantrex Inverter?
- M
  morriscarrieAug 28, 2025
  If you are reading a low output voltage (96 VAC–104 VAC) on your Xantrex Inverter, it could be due to: * Using a voltmeter that cannot accurately read the RMS voltage of a modified sine wave. Use a true RMS reading voltmeter such as the Fluke 87. * Low input voltage and the load is close to maximum allowable power. Check the connections and cable to see if the battery is fully charged. Recharge the battery if it is low. Reduce the load.
R
raymond41Aug 31, 2025
How to eliminate buzz in audio equipment when using a Xantrex XPower 1000 Inverter?
- G
  Gregory Santos Jr.Aug 31, 2025
  If you are hearing a buzz in your audio equipment when using a Xantrex Inverter, it's likely because the power supply in your audio system isn't adequately filtering the modified sine wave produced by the inverter. To fix this, use a sound system that has a higher quality power supply.
A
Anita JosephSep 3, 2025
Why does the low battery alarm stay on for my Xantrex XPower 1000 Inverter?
- J
  Jamie TaylorSep 3, 2025
  If the low battery alarm on your Xantrex Inverter stays on, it could be due to poor DC wiring or a battery in poor condition. To fix this, use the correct cable size and length for wiring, ensuring solid connections. You should also charge the battery or consider installing a new one.
P
Philip HarrisSep 5, 2025
What to do if my Xantrex XPower 1000 Inverter Power Light is on but there is no output voltage?
- N
  Nathan KimSep 5, 2025
  If your Xantrex Inverter's Power Light is on but there's no output voltage, the GFCI (Ground Fault Circuit Interrupter) may have tripped. Try resetting the GFCI.
B
Benjamin PittmanSep 8, 2025
How to improve television reception when using a Xantrex Inverter?
- P
  Paula StrongSep 8, 2025
  To improve television reception when using a Xantrex Inverter: ensure the chassis ground screw on the inverter's rear is firmly connected to your vehicle or home's ground system. Verify the television antenna provides a strong signal and use high-quality cables. Keep the cables between the battery and inverter short and twisted (two to three twists per foot). Position the television as far from the inverter as possible. Avoid operating high-power loads with the inverter while the television is on.
P
patrickjessicaSep 12, 2025
How to stop buzz in audio equipment when using a Xantrex XPower 1000?
- E
  Ebony NelsonSep 12, 2025
  A buzz in audio equipment when using a Xantrex Inverter can occur if the audio system's power supply doesn't adequately filter the modified sine wave produced by the inverter. Using a sound system with a higher quality power supply may resolve this issue.

Summary

About Xantrex

Contact Information

Provides contact details for Xantrex customer service and website.

Guide Overview

Purpose, Scope, and Audience

Outlines the guide's objective, content, and intended users.

Conventions and Related Info

Explains guide conventions and points to additional resources.

Safety Precautions

General Safety Instructions

Contains critical safety and operating instructions for the XPower Inverter 1000.

Battery Hazards and Precautions

Addresses risks of explosive gases, fire, explosion, and precautions when working with batteries.

Appliance Compatibility Warnings

Advises on potential equipment damage from the inverter's output waveform.

Product Features

Introduction and Key Features

Highlights quality power, ease of use, and comprehensive protection features.

AC and DC Panel Descriptions

Describes the AC and DC panels, including their components and functions.

Included Materials

Lists all the components included in the XPower 1000 package.

Installation Planning

Designing Your Installation

Guides the user through planning the inverter installation for optimal performance.

Installation Codes and Battery Requirements

Covers installation codes, calculating battery needs, and selecting charging systems.

Choosing an Appropriate Location

Details criteria for selecting a safe and suitable installation location for the inverter.

Cable and Fuse Sizing

Calculating Cable Sizes

Guides on calculating appropriate DC input and chassis ground cable sizes.

Calculating Fuse;Circuit Breaker Size

Explains how to determine the correct fuse or circuit breaker size for the battery.

Installing the XPower 1000

Pre-Installation Safety and Tools

Covers safety instructions, tools, and materials required before installation.

Mounting and Grounding Procedures

Details inverter mounting, overview of steps, and chassis ground connection.

DC Cable Connections

Provides step-by-step instructions for connecting the DC power cables.

Operation

Turning Inverter On;Off and Loads

Explains how to turn the inverter on/off, operate loads, and manage battery drain.

Operating Limits

Details power output and input voltage ranges for the inverter.

Inverter Load Considerations

Discusses inverter loads, high surge loads, and potential damage to appliances.

Routine Maintenance

Inverter Unit and Battery Care

Provides tasks for maintaining the inverter unit and batteries.

Troubleshooting

Common Problems and Solutions

Addresses common issues like audio buzz, TV interference, and provides reference solutions.

Specifications

Electrical and Physical Specs

Details electrical performance, physical dimensions, and weight of the XPower 1000.

Mounting Templates

Provides dimensional diagrams for mounting the inverter.

Battery Management

Battery Types and Sizing Basics

Explains battery types, sizing importance, and capacity ratings.

Estimating Battery Needs

Guides users on calculating battery capacity and managing multiple batteries.

Battery Tips and Connections

Covers battery care, gas hazards, temperature effects, and connection best practices.

Charging Systems

Charging System Requirements

Details necessary charging system capabilities for battery health.

Charging Methods Overview

Discusses charging via alternators, AC power, and alternative energy sources.

Warranty and Return Information

Warranty Details and Exclusions

Details warranty terms, proof of purchase, and limitations on coverage.

Return Procedures

Outlines the policy for obtaining RMA and shipping products for service.

Out of Warranty Service

Explains the process and fees for servicing units outside the warranty period.

System Information for Service

Provides a form to record system details for customer service inquiries.

Xantrex XPower 1000 Specifications

General

Output Voltage	120 VAC
Output Waveform	Modified Sine Wave
Input Voltage	12 VDC
Weight	9.5 lbs
Output Frequency	60 Hz
Efficiency	90%
Cooling	Fan Cooled
Output Power	1000 Watts
Surge Power	2000 Watts
Protections	Overload