Xerox CopyCentre C123 Service Manual (English)

Other manuals for Xerox CopyCentre C123

Service Manual22 pages

User Guide360 pages

Brochure & Specs6 pages

Quick Reference Guide154 pages

Scan Guide28 pages

Quick Installation Card2 pages

Questions and Answers:

M
Mr. David GloverAug 28, 2025
Why is my Xerox All in One Printer producing blank output?
- T
  Theresa TravisAug 28, 2025
  If your Xerox All in One Printer is producing blank output, check that the document is loaded face up in the document feeder. If the drum cartridge is new, the toner may not be dispensing; try repeating the job. Ensure the seal tape has been removed from the new drum cartridge. Reinstall both the drum and toner cartridges. If problems persist, replace the drum cartridge, and if the screen prompts, replace the toner cartridge as well.
C
Carla SaundersAug 29, 2025
How to adjust print darkness on Xerox All in One Printer?
- L
  Lisa BishopAug 29, 2025
  If the output from your Xerox All in One Printer is too light or too dark, try loading fresh paper and check the quality of the original document. You can also select the Lighten/Darken option on the touch screen. Run off more prints to see if the copy quality improves. If the issue persists, consider replacing the drum cartridge.
G
Gerald MorrisAug 30, 2025
How to resolve a tray fault on Xerox All in One Printer?
- V
  Valerie HarrisAug 30, 2025
  To resolve a tray fault on your Xerox All in One Printer: 1. Open the paper tray. 2. Move the paper tray guides away from the paper. 3. Move the paper tray guides against the paper so that they are just touching the paper. 4. Power the machine off and then on.
J
Jessica SharpAug 25, 2025
What to do if Xerox All in One Printer displays a memory full error?
- B
  brandontaylorAug 25, 2025
  If your Xerox All in One Printer displays a memory full error message, check with the Key Operator about available memory. To resolve this, divide the remaining pages of the job into several smaller jobs and run them again.
M
Melody EvansAug 31, 2025
Why are images blurred on my Xerox All in One Printer?
- S
  Scott HopkinsAug 31, 2025
  If you're experiencing blurred images with your Xerox All in One Printer, try loading fresh paper. If the problem persists, replace the drum cartridge, and if the screen prompts, replace the toner cartridge.
E
Elizabeth HaneyAug 31, 2025
How to fix missing characters on Xerox All in One Printer output?
- F
  Faith BarnesAug 31, 2025
  If your Xerox All in One Printer output is missing characters, try loading fresh paper. If that doesn't resolve the issue, reinstall the drum cartridge. If the problem continues, replace the toner cartridge, especially if the screen displays a replacement message.
M
Mariah DavisSep 1, 2025
Why Xerox All in One Printer doesn't show paper tray?
- N
  Nicholas RobertsSep 1, 2025
  If your Xerox All in One Printer does not display the Tandem Tray Module (or one of the paper trays) as a Paper Supply selection, ensure that all paper trays are fully closed. An ajar tray can prevent the machine from sensing its connection. Open and close each paper tray and the Tandem Tray Module. If the issue persists, power the machine off and then on again.
O
Oscar MillerSep 1, 2025
How to eliminate ghosting effect on Xerox All in One Printer?
- S
  Sarah LucasSep 2, 2025
  To address ghosting issues on your Xerox All in One Printer, check the quality of the documents. If you're using transparencies, select [Transparency] in [Paper Type] to allow the machine to adjust the quality automatically. Ensure you feed the document SEF (Short Edge Feed). If the problem persists, replace the drum cartridge.
K
karen00Sep 2, 2025
How to resolve solid density variations on Xerox All in One Printer?
- K
  Katelyn HowellSep 2, 2025
  To resolve solid density variations on your Xerox All in One Printer, start by checking the quality of the documents. If necessary, select [Lighten/Darken] on the touch screen to adjust the density. If the issue persists, consider replacing the drum cartridge.
O
ohowardSep 3, 2025
Why is the Finisher/Stapler option missing on my Xerox All in One Printer?
- C
  christophergarciaSep 3, 2025
  If the Finisher/Stapler option is not displayed on your Xerox All in One Printer, check that the cables from the finisher are securely connected to the machine. Also, ensure that the Finisher is correctly positioned. The machine automatically configures itself when additional options are attached.