EasyManuals Logo

Xerox Phaser 8560 Service Manual

Xerox Phaser 8560
29 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #6 background imageLoading...
Page #6 background image
iv Phaser 8400/8500/8550/8560 Color Printer Service Manual
Symbols Marked on the Product
Read and obey all posted warning labels. Throughout the printer, warning
labels are displayed on potentially dangerous components. As you service the
printer, check to make certain that all warning labels remain in place.
Power Safety Precautions
Power Source
For 115 VAC printers, do not apply more than 135 volts RMS between the
supply conductors or between either supply conductor and ground. For 230
VAC printers, do not apply more than 254 volts RMS between the supply
conductors or between either supply conductor and ground. Use only the
specified power cord and connector. This manual assumes that the reader is
a qualified service technician.
Plug the three-wire power cord (with grounding prong) into a grounded AC
outlet only. If necessary, contact a licensed electrician to install a properly
grounded outlet. If the product loses its ground connection, contact with
conductive parts may cause an electrical shock. A protective ground
connection by way of the grounding conductor in the power cord is essential
for safe operation.
Disconnecting Power
W
arn
i
ng
The power switch does not completely de-energize the printer. You must
also disconnect the power cord from the printers AC inlet. Disconnect the
power cord by pulling the plug, not the cord.
Disconnect the power cord in the following cases:
if the power cord or plug is frayed or otherwise damaged,
if any liquid or foreign material is spilled into the product,
if the printer is exposed to any excess moisture,
if the printer is dropped or damaged,
if you suspect that the product needs servicing or repair,
whenever you clean the product.
Use caution (or draws attention to a particular component). Refer
to the manual(s) for information.
Hot surface on or in the printer. Use caution to avoid personal
injury.

Other manuals for Xerox Phaser 8560

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Xerox Phaser 8560 and is the answer not in the manual?

Xerox Phaser 8560 Specifications

General IconGeneral
ColorYes
Duplex printingNo
Print technologyLaser
Maximum resolution2400 x 600 DPI
Time to first page (color, normal)5 s
Print speed (black, normal quality, A4/US Letter)3 ppm
Print speed (color, normal quality, A4/US Letter)30 ppm
Maximum internal memory1 MB
Sound power level (standby)33 dB
Sound pressure level (printing)54 dB
Maximum duty cycle85000 pages per month
Number of print cartridges4
Page description languagesPCL 5c
Maximum input capacity625 sheets
Paper tray 2 input capacity525 sheets
Multi-Purpose tray input capacity100 sheets
Power requirements110 - 240 V, 50/60 Hz
Networking features10/100BaseTX
Standard media sizes140 x 216 mm - 216 x 356 mm
Power consumption (active)230 W
Compatible operating systemsLinux, Mac OS X 10.2 +, Novell NetWare 3.x +, Windows 2000 +
Envelopes sizesC5, DL
Maximum print size216 x 356 mm
Paper tray media typesBond paper, Envelopes, Glossy paper, Labels, Plain paper, Recycled paper, Transparencies
Non-ISO print media sizesExecutive (184 x 267mm), Legal (media size), Letter (media size), Statement (140 x 216mm)
ISO A-series sizes (A0...A9)A4, A5, A6
ISO B-series sizes (B0...B9)B5
Maximum ISO A-series paper sizeA4
Supported network protocols (IPv4)IPv6
Sustainability certificatesENERGY STAR
Power consumption (PowerSave)43 W
Storage temperature (T-T)-30 - 60 °C
Operating temperature (T-T)10 - 32 °C
Storage relative humidity (H-H)10 - 95 %
Operating relative humidity (H-H)10 - 80 %
Weight and Dimensions IconWeight and Dimensions
Dimensions (WxDxH)406 x 533.4 x 368 mm

Related product manuals